Pentek nsf us-1000 User Manual

Page of 8
Technical Support: 800.861.8758 (M-F 7:30 a.m. - 5:00 p.m. CST)
MTBE Filtration System 
Installation and Operating Instructions 
Model US-1000
Specifications
Temperature Range: 
40–100°F (4.4–37.8°C)
Pressure Range: 
30–125 psi (2.1–8.62 bar)
Service Flow Rate @ 60 psi (4.1 bar):  0.6 gpm (2.3 L/min)
Rated Service Life: 
1,000 gallons (3,785L)
Dimensions: 
 9.18 in. x 4.70 in. x 12.72 in. 
(233 mm x 119 mm x 323 mm)
Weight: 
6 lbs. (2.7 kg)
Parts Included
•  Filter system with filter cartridges – P-250A Cartridge Set
•   Installation hardware 
(mounting screws, T-Adapter, quick-connect elbows)
•  Housing wrench
•  Lead-free drinking water faucet
•  1/4" plastic tubing
Precautions
WARNING:
 Do not use with water that is microbiologically unsafe 
or of unknown quality without adequate disinfection before or after 
the system. Systems certified for cyst reduction may be used on 
disinfected waters that may contain filterable cysts. 
CAUTION:
 Filter must be protected against freezing, which can 
cause cracking of the filter and water leakage.
CAUTION:
 The rubber O-ring provides the water-tight seal between 
the cap and the bottom of the housing. It is important that the O-ring 
be properly seated in the groove below the threads of the housing or a 
water leak could occur.
CAUTION:
 Because of the product’s limited service life and to 
prevent costly repairs or possible water damage, we strongly 
recommend that the bottom of all plastic housings be replaced every 
ten years.  If the bottom of your housing has been in use for longer 
than this period, it should be replaced immediately. Date the bottom of 
any new or replacement housing to indicate the next recommended 
replacement date.
Tools and Materials 
Required
•  Safety glasses
•   Hand or electric drill 
(cordless recommended)
•  1/4" drill bit
•  File
•  Phillips head screwdriver
 
•   Adjustable wrench or 7/16” 
open-end wrench
•   Tube cutters or utility knife
If sink does not have hole for 
separate faucet:
•  Center punch
•  3/4" drill bit or hole saw
NOTE: 
•  For cold water use only.
•   Make certain that installation complies with all state and local 
laws and regulations.
•   The contaminants or other substances removed or reduced by 
the selected cartridge are not necessarily in your water. Ask your 
local water municipality for a copy of their water analysis, or have 
your water tested by a reputable water testing lab. 
•   After prolonged periods of non-use (such as during a vacation) it 
is recommended that the system be flushed thoroughly. Let water 
run for 5–6 minutes before using.
•   The filter cartridges used with this system have a limited service 
life.  Changes in taste, odor, and/or flow of the water being filtered 
indicate that the cartridge should be replaced.
About Your PENTEK MTBE Filtration 
System
Thank you for purchasing a PENTEK MTBE Filtration System. With 
only minimal maintenance, your new system will provide you with 
safer, better-tasting water for years to come. The filter cartridges 
should be changed after every 500 gallons of use or once every six 
months, whichever comes first. Filter life will vary depending on usage 
and water conditions. Changes in taste, odor, and/or flow of the water 
being filtered indicate that the filter cartridges should be replaced. 
US-1000 MTBE Filtration System
The US-1000 MTBE Filtration System uses two carbon filter cartridges 
specially formulated to provide safer, cleaner, and better-tasting 
water. The US-1000 filtration system is NSF certified to reduce MTBE, 
chlorine taste & odor, asbestos reduction and cyst removal, lead, 
mercury and VOC’s in drinking water (see performance data on p. 7 for 
specific claims).
Lead is tasteless and colorless, and may enter your water supply 
through lead pipes, lead solder, and brass fittings and faucets. The 
US-1000 system has been Tested and Certified by NSF International to 
reduce lead below the USEPA Action Level.
The Model US-1000 is Tested and Certified by NSF 
International against NSF/ANSI Standard 42 for the reduction 
of Taste and Odor, Chlorine, and Particulate Class I. Standard 
53 for the reduction of MTBE, Lead, Mercury, VOC, Cyst, 
Asbestos, and Turbidity.
 
146597   JA05