Philips AZ1226 User Manual

AC power cord

1)

1 TUNING – tunes to radio stations

2 MW•FM – selects wavebands, MW or FM

3 Cassette recorder keys:

; – pauses playback or recording

9/

– stops playback or recording.
– opens the cassette holder.

5 or 6 – fast winds/rewinds 

the tape

1 – starts playback

0 – starts recording

4

2; - starts or pauses disc playback.

5 SEARCH 

∞ § – skips or searches a 

passage/track backward or forward.

6

9 – stops disc playback;

– erases a program;

7 Cassette door

8 ALBUM+ (up)

– For MP3-CD only: select albums 

9 PROG – programs tracks and reviews the

program

0 MODE – selects different play modes:

e.g. REPEAT or SHUFFLE (random order)

! DBB (DYNAMIC BASS BOOST)

– turns the bass enhancement on/off.

@ VOLUME – adjusts volume level
# Display – shows disc functions

$ Source selector : CD/MP3, RADIO,

TAPE/OFF
– selects CD/MP3-CD, radio or  tape source

of sound

– switches off the set

% LIFT TO  OPEN  – lift here to open the disc

door

^ Telescopic antenna - improves FM 

reception.

& p - 3.5mm stereo headphone jack

* Voltage selector – (not for all versions)

adjust to match the local voltage 110/220V
before plugging in the set.

( Battery door - open to insert 6 x 1.5V 

/ UM2/ C-cells.

) AC MAINS - inlet for power cord.

Whenever convenient, use the power supply
cord if you want to conserve battery life.
Make sure you remove the plug from the set
and wall outlet before inserting batteries.

Open the battery compartment and insert
six batteries, type R-14, UM-2 or C-cells,
(preferably alkaline) with the correct polarity
as indicated by the "+" and "–" symbols inside
the compartment (See 1).

Replace the compartment door, making sure
the batteries are firmly and correctly in place.
The set is now ready to operate.

Incorrect use of batteries can cause 
electrolyte leakage and will corrode the 
compartment or cause the batteries to burst:

Do not mix battery types: e.g. alkaline with
carbon zinc. Only use batteries of the same
type for the set.

When inserting new batteries, do not try to
mix old batteries with the new ones.

Remove the batteries if the set is not to be
used for a long time.

Check if the power/mains voltage, as shown
on the type plate located on the 
bottom of the set,

corresponds to your

local power supply. If it does not, consult your
dealer or service center.

If your set is equipped with a voltage 
selector, adjust the selector so that it 
matches with the local power supply.

Connect the power cord to the
AC MAINS

inlet and the wall socket.The

set is now ready for use.

To switch the set off completely, withdraw
the power cord from the wall socket.

•

Disconnect the power cord from the wall
socket to protect your set during heavy 
thunderstorms.

Helpful hints:
–

To avoid unnecessary energy consumption,
always adjust the source selector to
TAPE/OFF

after using the set. Also check

that the tape deck keys are released.

To switch on, adjust the source selector to
CD/MP3

, RADIO or TAPE/OFF as

desired.

To switch off, adjust the source selector to
TAPE/OFF

and check the cassette keys are

released.

Adjusting volume and sound
Adjust the sound with the VOLUME and
DBB

(Dynamic Bass Boost) controls.

Push the source selector to RADIO.

Adjust the MW•FM to MW or FM to
select your desired waveband.

Turn TUNING to tune to a radio station.

To switch off the radio, adjust the source
selector

to TAPE/OFF and check the

cassette keys are released.

For FM, extend, incline and turn the 
telescopic antenna. Reduce its length if the
signal is too strong.

For MW, uses a built-in antenna. Direct this
antenna by turning the whole set.