Philips AZ1017 User Manual

•

Place the set on a hard, flat and stable surface
so that the system does not tilt.

•

Do not expose the set, batteries, CDs to
humidity, rain, sand or excessive heat caused
by heating equipment or direct sunlight.

•

Do not expose the apparatus to dripping or
splashing.

•

Adequate ventilation with a minimum gap of
6 inches between the ventilation holes and
surrounding surfaces is necessary to prevent
heat build-up.

•

The ventilation should be impeded by cover-
ing the ventilation openings with items, such
as newspapers, table-cloths, curtains, etc..

•

No objects filled with liquids, such as vases,
shall be placed on the apparatus.

•

No naked flame sources, such as lighted can-
dles, should be placed on the apparatus.

•

The mechanical parts of the set contain 
self-lubricating bearings and must not be oiled
or lubricated.

•

To clean the set, use a dry cloth. Do not use
any cleaning agents containing alcohol,
ammonia, benzene or abrasives as these may
harm the housing.

To ensure quality recording and playback of
the tape deck, clean parts A, B and C as
shown, once a month. Use a cotton bud 
slightly moistened with alcohol or a special
head cleaning fluid to clean the deck.

Open the cassette holder by pressing 

9/.

Press

1 and clean the roller C.

Press 

; and clean the heads A, and the 

capstan B.

After cleaning, press 

9.

➜ Cleaning of the heads can also be done by

playing a cleaning cassette through once.

•

If the CD player cannot read CDs correctly,
use a cleaning CD to clean the lens before
taking the set to repair.

•

The lens of the CD player should never be
touched!

•

Sudden changes in the surrounding 
temperature can cause condensation on the
lens of your CD player. Playing a CD is then
not possible. Do not attempt to clean the
lens but leave the set in a warm environment
until the moisture evaporates.

•

Always close the CD-tape door to avoid dust
on the lens.

•

To clean the CD, wipe in a straight line from
the center towards the edge using a soft,
lint-free cloth. Do not use cleaning agents as
they may damage the disc.

•

Never write on a CD or attach any stickers
to it.

7)

Adjust the source selector to
TAPE/OFF

.

Press 

9/ to open the cassette holder, and

insert a cassette and close the deck.

Press 

1 to start playback.

To pause playback press 

;.

To resume, press 

; again.

To stop the tape, press 

9/.

Press 

5 or 6 until you reach your desired

passage.

Press 

9/ to stop rewinding/fast forwarding.

–

; has been activated.)

–

•

Recording is permissible insofar as copyright
or. other rights of third parties are not
infringed.

•

For recording, use only NORMAL type cas-
settes (IEC type I) on which the tabs have
not yet been broken.This deck is not suited
for recording on CHROME (IEC II) or
METAL (IEC IV) type cassettes.

•

The best recording level is set automatically.
Altering the VOLUME will not affect the
recording.

•

To protect a tape from accidental erasure,
break out the tabs. If you wish to record
again, cover the tabs with a piece of adhesive
tape.

Select CD source.

Insert a CD and if desired, program track
numbers.

Press 

9/ to open the cassette holder. Insert

a blank tape and close the deck.

Press

0 to start recording.

➜ Playing of the CD program starts 

automatically from the beginning of the 
program. It is not necessary to start the
CD player separately.

For brief interruptions press 

;.To resume

recording, press 

; again.

To stop recording, press 

9/.

Adjust the source selector to TUNER.

Adjust BAND to FM or MW as your
desired band.

Tune to the desired radio station (see Radio

).

Follow steps 3-6 under CD sychro start

.

Select TAPE source.

Follows steps 3-4 under Recording from
the CD Player.

Speak towards the built-in microphone 
(located on the left speaker, see 1).

Follows steps 6-7 under Recording from
the CD Player.