Hitachi cg32w460n User Manual
GB - 7 -
Before Switching on your TV
Power connection
IMPORTANT: The TV set is designed to operate on 220-240V
AC, 50 Hz.
• After unpacking, allow the TV set to reach the ambient room
AC, 50 Hz.
• After unpacking, allow the TV set to reach the ambient room
temperature before you connect the set to the mains.
Connections to the RF input socket
• Connect the aerial or cable TV plug into the RF input socket
on the back of the TV.If you are also connecting a video re-
corder /satellite receiver, plug the aerial into this equipment
first and then connect the RF output socket from this device
to the RF input on the back of the TV.
corder /satellite receiver, plug the aerial into this equipment
first and then connect the RF output socket from this device
to the RF input on the back of the TV.
VHF/UHF
75
Ω
TV REAR PANEL
CABLE TV
How to connect other devices
IMPORTANT: Switch off the TV before connecting any external
device.
Sockets for external connections are at the back of the TV. For
connection of other devices via Euroconnector refer to the
manuals of the related devices.
device.
Sockets for external connections are at the back of the TV. For
connection of other devices via Euroconnector refer to the
manuals of the related devices.
Inserting batteries in the remote control
handset
handset
• Place the batteries in the right directions as seen below.
• Remove the battery cover located on the back of the handset
• Remove the battery cover located on the back of the handset
by gently pulling upwards from the indicated part.
• Insert two AAA (R03) or equivalent type batteries inside.
• Replace the battery cover.
• Replace the battery cover.
NOTE: Remove batteries from remote control handset when it
is not to be used for a long period.Otherwise it can be damaged
due to any leakage of batteries.
is not to be used for a long period.Otherwise it can be damaged
due to any leakage of batteries.
Switching the TV ON/OFF
To switch the TV on
Your TV will switch on in two steps:
1- Press the power button located on the front of the TV. Then
1- Press the power button located on the front of the TV. Then
the TV switches itself to standby mode and the RED LED
located below the TV turns on.
located below the TV turns on.
2- To switch on the TV from stand-by mode either:
Press a digit button on the remote control so that a programme
number is selected,
or,
Press Programme Up or Down buttons on the front of the TV or
on the remote control, so that last switched off programme is
selected.
In either case the TV will switch on and the RED LED will turn
to GREEN.
Press a digit button on the remote control so that a programme
number is selected,
or,
Press Programme Up or Down buttons on the front of the TV or
on the remote control, so that last switched off programme is
selected.
In either case the TV will switch on and the RED LED will turn
to GREEN.
To switch the TV off
• Press the stand-by button on the remote control, so the TV will
switch to stand-by mode and the GREEN LED will become
RED,
RED,
or,
Press the power button located on the front of the TV, so the TV
will switch off and the GREEN LED will turn off.
Press the power button located on the front of the TV, so the TV
will switch off and the GREEN LED will turn off.
Operating the TV
You can operate your TV both using the remote control
handset and onset buttons.
handset and onset buttons.
A.P.S. (Automatic Programming System)
"PLEASE, CHECK ANTENNA CABLE. AUTO PROGRAM-
MING SYSTEM" message will be displayed when you turn
on your TV for the first time. A.P.S., searches and sorts all
channels and stores them automatically on your TV, accord-
ing to the transmission of programme systems in your area.
MING SYSTEM" message will be displayed when you turn
on your TV for the first time. A.P.S., searches and sorts all
channels and stores them automatically on your TV, accord-
ing to the transmission of programme systems in your area.
To cancel A.P.S. before starting, press “
TV
” button. First of
all choose the “COUNTRY”. This, will effect the sort process
in A.P.S.
The "STANDARD" setting is fixed to "BG". You cannot
change this item's setting.
in A.P.S.
The "STANDARD" setting is fixed to "BG". You cannot
change this item's setting.
To select “START” use “ “ or “ ” button and press “ ” or
“ ” button. To cancel A.P.S. during running press “ ” or
“ ” button.
“ ” button. To cancel A.P.S. during running press “ ” or
“ ” button.
PLEASE CHECK ANTENNA CABLE
AUTO. PROGRAMMING SYSTEM
COUNTRY
STANDARD
START
STANDARD
START
D
BG
BG
A.P.S. IS RUNNING
P 07 VHF1
CANCEL
After A.P.S. is finalized, a programme list will apper on the
screen. In the programme list you will see the programme
numbers and names assigned to the programmes.
If you do not accept the locations and / or the programme
names of programmes, you can change them in Programme
menu.
screen. In the programme list you will see the programme
numbers and names assigned to the programmes.
If you do not accept the locations and / or the programme
names of programmes, you can change them in Programme
menu.
01-ENG-(CG32W460AN)-3253W-3040-AK37-ST7P-PLLFS-APS-BG-50050266.p65
13.07.2004, 13:42
7