omnitron-systems-technolo 10-100m2 User Manual
When the upload is complete, the 10/100M2 displays the update status and then automatically restarts with
the newly loaded firmware.
the newly loaded firmware.
3.4.4.4
Updating the 10/100M2 Firmware via FTP
Using an FTP application, upload the new firmware into the FTP root directory of the 10/100M2. When
the file transfer is complete, the 10/100M2 verifies the file and then automatically restarts with the newly
loaded firmware.
the file transfer is complete, the 10/100M2 verifies the file and then automatically restarts with the newly
loaded firmware.
For detailed instruction on updating the management modules and other modules in the same chassis via
FTP, download the application note “iConverter Management: Updating Modules via FTP” available on
Omnitron’s web page:
FTP, download the application note “iConverter Management: Updating Modules via FTP” available on
Omnitron’s web page:
http://www.omnitron-systems.com/downloads.php
See Setting 10/100M2 Passwords Section 3.4.1.4, on how to configure FTP.
3.5
VERIFY OPERATION
PI
SA
Once the module has been installed and configured, per Sections 3.2 - 3.4, verify the module is operational
by viewing the status of the LED indicators. The table below provides a description for each LED indicator.
by viewing the status of the LED indicators. The table below provides a description for each LED indicator.
The Power LED indicates the module is receiving power from the chassis or power cord. The plug-in
modules has an LED indicator for each available power supply in the chassis (the 19-Module Chassis has
three, the 5-Module Chassis has two).
modules has an LED indicator for each available power supply in the chassis (the 19-Module Chassis has
three, the 5-Module Chassis has two).
The Fiber Optic “FO” LED indicates the fiber optic connection has been established. A blinking LED
indicates the presence of data.
indicates the presence of data.
The UTP “10/100” LED indicates the module has established a connection across its UTP port. A blinking
LED indicates the presence of data.
LED indicates the presence of data.
Refer to Section 6.0, Troubleshooting Guide, for help in determining possible fault conditions.
PI
SA
PI
SA
LED Function
"Legend"
Color
Off State
On / Blinking State
On / Blinking State
Power "Pwr"
Green No power
On: Module has power
On: Module has power
Power Supply
Status #X
Status #X
Green
Chassis Power
Supply not installed
Supply not installed
On: Power available from
installed Power Supply #X
Blinking: No power available
installed Power Supply #X
Blinking: No power available
from installed Power Supply #X
Not available on standalone
100Mbps Fiber
Optics "FO"
Green No Fiber Link
On: Fiber link is active
Blinking: Fiber Data Activity
Blinking: Fiber Data Activity
On: Fiber link is active
Blinking: Fiber Data Activity
Blinking: Fiber Data Activity
Chassis
Management
Master/Slave
"BP"
Management
Master/Slave
"BP"
Green
Chassis Slave
Mode
Mode
On: Chassis Master Mode
Blinking: Operating in OAM
Mode
Blinking: Operating in OAM
Mode
Not available on standalone
UTP port
10Mbps "10"
Green 10Mbps not active
On: 10Mbps UTP link is active
Blinking: UTP Data Activity
Blinking: UTP Data Activity
On: 10Mbps UTP link is active
Blinking: UTP Data Activity
Blinking: UTP Data Activity
UTP port
100Mbps "100"
Green 100Mbps not active
On: 100Mbps UTP link is active
Blinking: UTP Data Activity
Blinking: UTP Data Activity
On: 100Mbps UTP link is active
Blinking: UTP Data Activity
Blinking: UTP Data Activity
UTP port Full-
Duplex "FDX"
Duplex "FDX"
Green
Half-Duplex when
any UTP link is
active
any UTP link is
active
Full-Duplex when any UTP link
is active
is active
Full-Duplex when any UTP link
is active
is active
Page 22