Chaney Instrument model 13123 User Manual
Mounting and Operating Instructions
1) Using the Wall Mounting Bracket as a guide, locate a suitable location for your double
sided clock. It is recommended that you locate the mounting bracket on a wall stud for a
secure installation. Mark the location of the 4 holes using the mounting bracket as a
template. Be sure it is plumb or the mounting bracket will not be vertical. (Step 1 on the
Assembly Instruction diagram)
2) a) If you are attaching the mounting bracket directly to a wall stud there will be no
need to use the wall anchors provided. Instead, drill 4 pilot holes into the studs. Mount
the wall bracket using the enclosed screws.
b) If you are not installing the mounting bracket directly into a wall stud you will need
to locate the holes as described above. Drill 4 holes just large enough to accept the wall
anchors. Attach the mounting bracket to the wall anchors using the screws provided.
3) Insert 1 fresh alkaline “AA” battery into each battery compartment by sliding off the
battery compartment covers located along the rim of the clock case. Be sure to follow the
polarity shown in the battery compartment. Replace the covers. (see the diagram below)
* PLEASE NOTE - be careful to insert the battery in the correct direction. Inserting the
battery with the + and – in the wrong direction will reset the internal calendar and will
result in your clock not resetting itself correctly for Daylight Saving Time.
4) Using the Key provided set the clocks to the correct local time by inserting the key
into the openings in the case frame and rotating it in either direction until the correct time
is shown (see the diagram below). Be sure to keep your keys in a secure location so you
can adjust the time as necessary.
5) Carefully insert the stem of the clock case into the opening in the wall mounting
bracket. Use the fastener screw provided to lock it in place. (Step 2 on the Assembly
Instructions)
6) Attach the enclosed finial to the opening on the bottom of the wall mounting bracket.
(see the diagram on the assembly instructions sheet)
7) Your clock should require no further adjustment. Twice a year it will automatically
adjust itself for Daylight Saving Time. If you live in an area that does not follow DST
you can use the key to adjust the time back to Standard Time.
sided clock. It is recommended that you locate the mounting bracket on a wall stud for a
secure installation. Mark the location of the 4 holes using the mounting bracket as a
template. Be sure it is plumb or the mounting bracket will not be vertical. (Step 1 on the
Assembly Instruction diagram)
2) a) If you are attaching the mounting bracket directly to a wall stud there will be no
need to use the wall anchors provided. Instead, drill 4 pilot holes into the studs. Mount
the wall bracket using the enclosed screws.
b) If you are not installing the mounting bracket directly into a wall stud you will need
to locate the holes as described above. Drill 4 holes just large enough to accept the wall
anchors. Attach the mounting bracket to the wall anchors using the screws provided.
3) Insert 1 fresh alkaline “AA” battery into each battery compartment by sliding off the
battery compartment covers located along the rim of the clock case. Be sure to follow the
polarity shown in the battery compartment. Replace the covers. (see the diagram below)
* PLEASE NOTE - be careful to insert the battery in the correct direction. Inserting the
battery with the + and – in the wrong direction will reset the internal calendar and will
result in your clock not resetting itself correctly for Daylight Saving Time.
4) Using the Key provided set the clocks to the correct local time by inserting the key
into the openings in the case frame and rotating it in either direction until the correct time
is shown (see the diagram below). Be sure to keep your keys in a secure location so you
can adjust the time as necessary.
5) Carefully insert the stem of the clock case into the opening in the wall mounting
bracket. Use the fastener screw provided to lock it in place. (Step 2 on the Assembly
Instructions)
6) Attach the enclosed finial to the opening on the bottom of the wall mounting bracket.
(see the diagram on the assembly instructions sheet)
7) Your clock should require no further adjustment. Twice a year it will automatically
adjust itself for Daylight Saving Time. If you live in an area that does not follow DST
you can use the key to adjust the time back to Standard Time.