Hitachi 27cx21b User Manual
CABLE/SATELLITE AND VCR CODES
19
1. Turn on your cable/satellite box.
2. Aim the remote control at the front of your cable/satellite box.
3. Press the CABLE button to switch to cable/satellite box mode.
4. While holding down the CABLE button, enter the two digit preset code that matches your cable/satellite box.
The remote will turn off your cable/satellite box when the correct two digit preset code is entered. When this
occurs, the remote control is programmed for your cable/satellite box. If the cable/satellite box does not turn off
after five seconds, try another two digit preset code.
5. The remote will now control your cable/satellite box.
2. Aim the remote control at the front of your cable/satellite box.
3. Press the CABLE button to switch to cable/satellite box mode.
4. While holding down the CABLE button, enter the two digit preset code that matches your cable/satellite box.
The remote will turn off your cable/satellite box when the correct two digit preset code is entered. When this
occurs, the remote control is programmed for your cable/satellite box. If the cable/satellite box does not turn off
after five seconds, try another two digit preset code.
5. The remote will now control your cable/satellite box.
NOTES:
1. If your cable/satellite box cannot be operated after performing the above procedures, your cable/satellite box
code has not been precoded into the remote.
2. In the unlikely event that your cable/satellite box cannot be operated after performing the above procedures,
please consult your cable/satellite box operating guide.
3. The remote control will remember the codes you have programmed in until the batteries are removed from the
remote control. After replacing the batteries repeat the entire programming procedure stated above.
4. If your cable/satellite box does not have a power function, the remote will issue the CHANNEL UP (
1. If your cable/satellite box cannot be operated after performing the above procedures, your cable/satellite box
code has not been precoded into the remote.
2. In the unlikely event that your cable/satellite box cannot be operated after performing the above procedures,
please consult your cable/satellite box operating guide.
3. The remote control will remember the codes you have programmed in until the batteries are removed from the
remote control. After replacing the batteries repeat the entire programming procedure stated above.
4. If your cable/satellite box does not have a power function, the remote will issue the CHANNEL UP (
)
function.
1 CABLE Button
This button allows the remote to control your cable/satellite box by setting it to CABLE/SATELLITE mode.
2 PRECODED CABLE/SATELLITE BOX Buttons
These buttons transmit the chosen precoded CATV and satellite codes.
3 TV/VCR Button
When the remote is in CABLE/SATELLITE mode, this is the A/B button.
4 LST-CH Button
If your cable/satellite box has an enter function, this button will send the cable/satellite box enter code.
5 RECALL/EXIT/CS (COMMERCIAL SKIP) Button
If your cable/satellite box does not have a last channel function, this button will send the TV channel recall code.
6 EXCLUSIVE TV Buttons
These buttons are for operating the TV.
This button allows the remote to control your cable/satellite box by setting it to CABLE/SATELLITE mode.
2 PRECODED CABLE/SATELLITE BOX Buttons
These buttons transmit the chosen precoded CATV and satellite codes.
3 TV/VCR Button
When the remote is in CABLE/SATELLITE mode, this is the A/B button.
4 LST-CH Button
If your cable/satellite box has an enter function, this button will send the cable/satellite box enter code.
5 RECALL/EXIT/CS (COMMERCIAL SKIP) Button
If your cable/satellite box does not have a last channel function, this button will send the TV channel recall code.
6 EXCLUSIVE TV Buttons
These buttons are for operating the TV.
CABLE/SATELLITE AND VCR CODES
The remote control is capable of operating many brands of VCRs and cable boxes. You must first program the
remote control to match the remote system in your VCR or cable box.
remote control to match the remote system in your VCR or cable box.
NOTE: The remote control memory is limited. Some models of VCRs or cable boxes may not operate. The
remote control is not designed to control all features that are available in all models.
remote control is not designed to control all features that are available in all models.
VCR
BRAND
CODES
Emerson
00, 01, 10, 16, 23, 33, 37, 40, 41, 43, 44, 50, 51, 52
Funai
00
GE
09,
22,
24,
39
Hitachi
14,
15,
24,
31
JVC
02,
14,
26
Magnavox
09, 12, 28, 32, 34
Mitsubishi
16, 23, 26, 36, 49
Panasonic
09, 35, 46, 47, 53
RCA
15, 22, 24, 31, 34, 39
Sony
06,
07,
08,
09
Toshiba
6,
17,
25,
44
Zenith
07,
08,
12