Hanna Instruments hi 99141 User Manual

w w w . h a n n a i n s t . c o m

This Instrument is in Compliance

with the CE Directives

Dear Customer,
Thank you for choosing a Hanna Instruments
Product.
Please read this instruction manual carefully
before using the instrument. This manual will
provide you with all the necessary informa-
tion for the correct use of the instrument, as
well as a precise idea of its versatility in a
wide range of applications.
This instrument is in compliance with the 
directives.

All Hanna Instruments meters are warranted
for two years against defects in workmanship
and materials when used for their intended pur-
pose and maintained according to instructions. The
probes are warranted for a period of six
months.

This warranty is limited to repair or replacement
free of charge. Damages due to accident, misuse,
tampering or lack of prescribed maintenance are
not covered.

If service is required, contact the dealer from whom
you purchased the instrument. If under warranty,
report the model number, date of purchase, serial
number and the nature of the problem. If the repair
is not covered by the warranty, you will be notified
of the charges incurred. If the instrument is to be
returned to Hanna Instruments, first obtain a Re-
turned Goods Authorization Number from the Cus-
tomer Service department and then send it with
shipment costs prepaid. When shipping any instru-
ment, make sure it is properly packaged for com-
plete protection.

Remove the instrument from the packing ma-
terial and examine it carefully to make sure
that no damage has occurred during ship-
ment. If noticeable damage is evident, notify
your dealer.

Note: Save all packing material until you

are sure that the instrument functions
correctly. All defective items must be
returned in the original packing to-
gether with the supplied accessories.

HI  99141 is a portable, microprocessor-
based pH and temperature meter with a
special probe.
HI 72911 is a rugged double junction pH
electrode with a flat tip and stainless-steel
body that also functions as a matching pin.
The electrode has an annula PTFE junction
 for maximum surface contact and the
flat tip is easy to clean and prevents solids
in solution from collecting on the sensor.
Moreover, a built-in temperature sensor al-
lows simultaneous pH and temperature
readings and a mini amplifier renders mea-
surements impervious to noise and electri-
cal interferences.

Each meter comes with:

•

  HI 72911 pH/temperature probe

•

 3x1.5V AA alkaline batteries

• 

instruction manual

• 

plastic carrying case

-2.00 to 16.00 pH

-5.0 to 105.0°C / 23.0 to 221.0°F

0.01 pH

0.1°C / 0.1°F

±0.02 pH

±0.5°C up to 60°C; ±1°C outside

±1°F up to 140°F; ±2°F outside

±0.02 pH

±0.2°C or ±0.4°F

Automatic

Automatic, 1 or 2 point

with 2 sets of standardized buffers

(4.01/7.01/10.01 or 4.01/6.86/9.18)

amplified pH-electrode with built-in tempera-

ture sensor and matching pin

3 x 1.5V AA / IEC LR6

approx. 1500 hours

after 8 minutes of nonuse

0 to 50°C (32 to 122°F);

RH 100%

150x80x38 mm (5.9x3.2x1.5”)

245 g (8.6 oz.)

To clean the meter, it is recommended to use water.

Hanna Instruments reserves the right to modify
the design, construction and appearance of its
products without advance notice.

Combination amplified pH elec-
trode with built-in temperature
sensor, flat tip and stainless-
steel body

pH 4.01 buffer solution, 500 mL

pH 6.86 buffer solution, 500 mL

pH 7.01 buffer solution, 500 mL

pH 9.18 buffer solution, 500 mL

pH 10.01 buffer solution, 500 mL

Storage solution, 460 mL

Cleaning solution, 460 mL

Cleaning solution for salt depos-
its on electrodes, available in 20
mL sachet (25 pcs.), 230 mL and
460 mL bottle

Cleaning & disinfection solution
for algae, fungi & bacteria, avail-
able in 20 mL sachet (25 pcs.),
230 mL and 460 mL bottle

Hard carrying case

Blue shockproof rubber boot

Electrode holder

1. Automatic Temperature Compensation
    indicator
2. Stability indicator
3. Battery percentage
4. pH calibration indicator
5. Low battery indicator
6. Selectable temperature unit
7. Secondary display
8. Primary display
9. Measuring unit for primary display

    

ISTR99141R2   06/03