DOD fx86 User Manual
WHAT
THE FX86B DOES
The FX86B creates a grinding wall of noise perfect for
harmonic corruption of the highest order.
The FX86B
emulates the death metal and grindcore sounds of Napalm
Death. Carcass, Brutal T
ruth, Pungent Stench, and others.
One advantage of the FX86B is it will oscillate when the
R.I.P . (LEVEL) control is turned up, allowing oscillation at
any amp volume. There is no distortion control. W
e just
maxed it out and tore it off!
CONNECTING THE FX86B
Connect your guitar to the input of the FX86B. Connect the
OUTPUT of the FX86B to your amp (or to the input of
another effects device you may be running).
T o eliminate the
need for a 9-volt battery, attach the DOD PS200R power
supply to the AC adapter jack.
FEATURES
LED indicator shows status of effect and battery condition.
Active switching for noiseless operation.
Easy access battery compartment.
Adapter jack for AC operation.
Rugged die-cast metal case.
Three year limited warranty.
Rubber non-skid bottom.
CONTROLS
R.I.P . (LEVEL): Matches the distortion level with original
signal level.
CAUTION: T
urning the R.I.P . (LEVEL) control clockwise
may cause some varieties of cats to gather and fight with
one another (this can easily be rehearsed for future
performances). T
urning the control counterclockwise can be
useful for a little midnight thrashing to avoid an encounter
with large numbers of law enforcement personnel.
GUTS (LOW): This controls the low end of the distortion
sound. T
urn it up to make your speakers groan.
PAIN (MID):
This controls the mid frequencies
of the distortion. By turning it down the low end becomes a
monster.
Turn it up and you will begin to feel the P
AIN!
SCREAM (HIGH): Controls the amount of high end on the
distortion. T
urn it up for brutal chainsaw pick attack! Note:
DOD will not be held responsible for any damage caused by
those “formally dead” who are suddenly awakened by the
FX86B.
FOOTSWITCH: Switches the distortion effect in or out of the
signal path.
LED INDICAT
OR: Lights when the distortion is enabled, and
is not lit when the distortion is bypassed.
JACKS: Input, Output, AC
Adapter (use the DOD PS200R
power supply to eliminate the need for a 9 volt battery).
OPERATION OF
THE FX86B
The FX86B is a high-gain effect designed to rattle bones,
(dead ones or live ones). This is not a pedal for the faint
of heart (or perhaps it is)! We
cranked the distortion flat
out and added three EQ control: GUTS (LOW), PAIN
(MID), and SCREAM (HIGH).
Alternate guitar or bass tunings aid in the quest to raise
the dead with music. T
ry tuning to C# (C#, F#, B, E, G#,
C#) or C (C, F , Bb, Eb, G, C).
This will give your guitar or
bass that mean tone. What more do you need? A
lobotomy!
When setting up the effect, use the R.I.P
. (LEVEL)
control to match the level of the distortion effect with the
level of the original input signal. The control should be
set so that there is a slight increase in level when the
effect is switched into the signal path.
The GUTS (LOW) knob controls the low-frequency (bass)
content of the signal (when the effect is on).
Turning this
control clockwise increases the low-
frequency content of the signal.
The SCREAM (HIGH) knob control the high-frequency
(treble) content of the guitar signal (when the effect is
on). This control adds more edge to your sound, allowing
your guitar sound to shatter glass (or at least sound like
it).
The PAIN (MID) knob controls the mid-frequencies and
can make your skin crawl if turned up. When it’s turned
down, it makes the GUTS (LOW) and SCREAM (HIGH)
controls even more effective.
On the following pages, some examples of different types
of sounds are shown, along with graphic representations
of how to set the knobs. Since good (or bad) guitar sounds
are a subjective matter, use these examples as starting
points to create your own sounds that meet your specific
tastes, or lack thereof.
This guitar sound is sure to destroy some speakers. The
dropped mids enhance the bass and highs.
This hard sound has a slight drop in the mids that gets the
point across instantly.
This sound is a wall of noise with an ultra low, low end and
blaring highs
IMPORTANT NOTES
• The FX86B battery is in use whenever the INPUT jack is
plugged in. If you are not using the FX86B, be sure to
unplug the cable from INPUT jack. This will prevent
unnecessary battery drain.
• The FX86B battery is in use whenever the INPUT jack is
plugged in. If you are not using the FX86B, be sure to
unplug the cable from INPUT jack. This will prevent
unnecessary battery drain.
• Remove the battery whenever the unit is not going to be
used for an extended period of time. This will prevent
possible damage due to leaking battery fluids.
used for an extended period of time. This will prevent
possible damage due to leaking battery fluids.
• If the FX86B fails to switch in or out, or the LED indicator
stays lit, the battery needs to be replaced.
stays lit, the battery needs to be replaced.
• Use of any AC adapter other than the DOD PS200R will
void the warranty of this product.
void the warranty of this product.
• Unauthorized repair of the FX86B will void the warranty.
Should your FX86B require service, contact your DOD FX
pedal dealer for return / repair information.
Should your FX86B require service, contact your DOD FX
pedal dealer for return / repair information.
DOD Warranty
1. The warranty registration card must be mailed within ten
days after purchase date to validate this warranty.
2. DOD warrants this product, when used solely within the
U.S., to be free from defects in materials and workmanship
under normal use and service.
days after purchase date to validate this warranty.
2. DOD warrants this product, when used solely within the
U.S., to be free from defects in materials and workmanship
under normal use and service.
3. DOD liability under this warranty is limited to repairing or
replacing defective materials that show evidence of defect,
provided the product is returned through the original dealer,
where all parts and labor will be covered up to a period of
three years. The company shall not be liable for any
consequential damage as a result of the product’s use in any
circuit or assembly.
replacing defective materials that show evidence of defect,
provided the product is returned through the original dealer,
where all parts and labor will be covered up to a period of
three years. The company shall not be liable for any
consequential damage as a result of the product’s use in any
circuit or assembly.
4. Proof-of-purchase is considered to be the burden of the
consumer.
consumer.
5. DOD reserves the right to make changes in design or
make additions to or improvements upon this product without
incurring any obligation to install the same on products
previously manufactured.
6. The foregoing is in lieu of all other warranties, expressed
or implied, and DOD neither assumes nor authorizes any
person to assume for it any obligation or liability in
connection with the sale of this product. In no event shall
DOD or its dealers be liable for special or consequential
damages or from any delay in the performance of this
warranty due to causes beyond their control.
make additions to or improvements upon this product without
incurring any obligation to install the same on products
previously manufactured.
6. The foregoing is in lieu of all other warranties, expressed
or implied, and DOD neither assumes nor authorizes any
person to assume for it any obligation or liability in
connection with the sale of this product. In no event shall
DOD or its dealers be liable for special or consequential
damages or from any delay in the performance of this
warranty due to causes beyond their control.
DECLARATION OF CONFORMITY
Manufacturer’s Name: DOD Electronics Corporation
Manufacturer’s Address: 8760 S. Sandy Parkway
Sandy, Utah 84070, USA
declares that the product
Product Name: FX86B
Product Options: All (requires a Class II power
adapter that conforms to the requirements of EN 60065,
EN 60742, or equivalent).
Safety: EN 60065 (1993)
IEC65 (1985) with Amendments 1,2,3
EMC: EN 55013: (1990)
EN 55020: (1991)
Supplementary Information:
The product herewith complies with the requirements of
the Low Voltage Directive 73/23/EEC and the EMC
Directive 89/336/EEC as amended by directive
93/68/EEC.
DOD Electronics Corporation
President of DOD
8760 S. Sandy Parkway
Sandy, Utah 84070, USA
Effective: August 26, 1997
European Contact: Your Local DOD Sales and
Service Office or
International Sales Office
3 Overlook Drive #4
Amherst, New Hampshire 03031, USA
Tel (603) 672-4244
Fax (603) 672-4246
DOD Electronics Corporation
8760 South Sandy Parkway
Sandy, Utah 84070
Telephone (801) 566-8800
FAX (801) 566-7005
International Distribution
3 Overlook Drive Unit 4
Amherst, New Hampshire 03031
U.S.A.
FAX (603) 672-4246
Copyright © 1998 DOD Electronics Corporation
Printed 2/98
FX86B 18-0038-B
A Harman International Company
DEATH METAL
DISTORTION
DISTORTION