brocade-communications-sy rfs6000 User Manual
Brocade Mobility RFS4000, RFS6000 and RFS7000 CLI Reference Guide
669
53-1001931-01
Wireless configuration commands
20
See also,
Usage Guidelines
To stop a service, use the
To stop a service, use the
no
command. For instance, use
no service wireless idle-radio-send-multicast enable
to stop sending
broadcast/multicast frames to idle radios
Example
RFController(config-wireless)#service show wireless ap-history
AP MAC Radio Timestamp Event Reason
===================================================================
00-A0-F8-BF-8A-4B N/A 20100926-20:23:10 Adoption N/A
RFController(config-wireless)#
RFController(config-wireless)#service show wireless mvlan 20
Wlan 20: pool_size =1
-----------------------------------------------------
[ 0]: wlan=20, vlan_id=1, limit=0, users=0, log_sent=0
[ 1]: wlan=20, vlan_id=0, limit=0, users=0, log_sent=0
[ 2]: wlan=20, vlan_id=0, limit=0, users=0, log_sent=0
[ 3]: wlan=20, vlan_id=0, limit=0, users=0, log_sent=0
[ 4]: wlan=20, vlan_id=0, limit=0, users=0, log_sent=0
[ 5]: wlan=20, vlan_id=0, limit=0, users=0, log_sent=0
[ 6]: wlan=20, vlan_id=0, limit=0, users=0, log_sent=0
[ 7]: wlan=20, vlan_id=0, limit=0, users=0, log_sent=0
[ 8]: wlan=20, vlan_id=0, limit=0, users=0, log_sent=0
[ 9]: wlan=20, vlan_id=0, limit=0, users=0, log_sent=0
[10]: wlan=20, vlan_id=0, limit=0, users=0, log_sent=0
[11]: wlan=20, vlan_id=0, limit=0, users=0, log_sent=0
[12]: wlan=20, vlan_id=0, limit=0, users=0, log_sent=0
[13]: wlan=20, vlan_id=0, limit=0, users=0, log_sent=0
[14]: wlan=20, vlan_id=0, limit=0, users=0, log_sent=0
[15]: wlan=20, vlan_id=0, limit=0, users=0, log_sent=0
•
free-packet-watermark <0-100>– The free packets
threshold in percent. If the percentage of free packets is
lower than this number, then additional packets will not be
queued in the datapath.
threshold in percent. If the percentage of free packets is
lower than this number, then additional packets will not be
queued in the datapath.
•
idle-radio-send-multicast enable – Enables forwarding
multicast packets to radios without associated wireless
clients.
multicast packets to radios without associated wireless
clients.
•
legacy-load-balance – Invoke legacy load balance algorithm.
•
map-radios <1-127> – Sets radio-to-cpu mapping constant
to a value in the range of 1 and 127.
to a value in the range of 1 and 127.
•
radio-misc-cfg <hex-bitmask> – Radio specific
miscellaneous U16 configuration for all radios.
miscellaneous U16 configuration for all radios.
•
rate-scale – Enable wireless rate scaling (default).
•
request-ap-log <1-1024> – Request AP Log for the selected
AP.
AP.
•
save-ap-log – Saves debug/error logs sent by the
access-point
access-point
•
snmp-trap-throttle <1-20> – Limits the number of SNMP
traps generated per second from the wireless module to a
number in the range 1 and 20.
traps generated per second from the wireless module to a
number in the range 1 and 20.
•
sync-radio-entries – sync radio configuration at cluster levels.
•
vlan-cache enable – Enables VLAN-cache mode.