Arkon AP036 Leaflet
AP020 AP013 AP036 | Dash or Console 3M™ Adhesive Mounting Disc
!
Airbag Warning
Do not install Arkon products over an airbag cover or within the air-
bag deployment zone. Arkon Resources, Inc. assumes no responsi-
bility of liability for injury or death as a result of car crashes and/or
airbag deployment.
Do not install Arkon products over an airbag cover or within the air-
bag deployment zone. Arkon Resources, Inc. assumes no responsi-
bility of liability for injury or death as a result of car crashes and/or
airbag deployment.
Arkon is not responsible for any damages caused to your car, your de-
vice, or yourself due to the installation or use of the pedestal mount.
vice, or yourself due to the installation or use of the pedestal mount.
The Mobile Mounting Specialists™
www.arkon.com
Arcadia, CA 91006 USA
Made in Taiwan
© Copyright 2007 Arkon Resources, Inc.
Consumer Hotline:
(USA) (800) 841-0884
(INT’L) (626) 254-9005
Mon-Fri. 9am-5pm, PST
(USA) (800) 841-0884
(INT’L) (626) 254-9005
Mon-Fri. 9am-5pm, PST
Package Contents:
(1) Self-adhesive dash or console pedestal mounting disc
(1) Alcohol cleaning pad
(1) Self-adhesive dash or console pedestal mounting disc
(1) Alcohol cleaning pad
No Tools Required for installation.
Choose a suitable location for disc (and pedestal) installation.
Do not place mount in or near an air bag deployment zone
or where it will obstruct view of the road or hinder vehicle
operation.
Do not place mount in or near an air bag deployment zone
or where it will obstruct view of the road or hinder vehicle
operation.
Clean the dash or console surface area thoroughly with the
included alcohol pad. Allow the area dry before applying the
mounting disc.
included alcohol pad. Allow the area dry before applying the
mounting disc.
Remove the paper backing of the disc and place on the
cleaned surface. Press the top of the disc down fi rmly to allow
the adhesive to stick to the surface. Allow 24 hours for the
adhesive to cure to the surface before applying any pressure.
cleaned surface. Press the top of the disc down fi rmly to allow
the adhesive to stick to the surface. Allow 24 hours for the
adhesive to cure to the surface before applying any pressure.
Step 1.
Step 2.
Step 3.
Dash or Console Mounting Instructions
AP020 Disc
(0 90 mm)
(0 90 mm)
AP013 Disc
(0 80 mm)
(0 80 mm)
AP036 Disc
(0 70 mm)
(0 70 mm)
Place the suction cup of the pedestal (sold separately) fi rmly down
on the center of the mounting disc and lower the securing lever.
on the center of the mounting disc and lower the securing lever.
Prepare the surface around the disc by applying a generous
amount of rubbing alcohol or similar adhesive removal product
to the area with a cotton swab. Let the liquid saturate the
adhesive area for about a minute.
amount of rubbing alcohol or similar adhesive removal product
to the area with a cotton swab. Let the liquid saturate the
adhesive area for about a minute.
Take a long piece of dental fl oss in each hand and slowly work
back and forth at the base of the adhesive disc. Gently use the
dental fl oss to cut the adhesive from the dash or console until
the black plastic disc is removed.
back and forth at the base of the adhesive disc. Gently use the
dental fl oss to cut the adhesive from the dash or console until
the black plastic disc is removed.
If the sticky adhesive area breaks apart or does not come off
completely, re-apply a small amount of alcohol (or adhesive
removal liquid) and carefully lift off the remaining area by hand.
completely, re-apply a small amount of alcohol (or adhesive
removal liquid) and carefully lift off the remaining area by hand.
Step 4.
Step 1.
Step 2.
Step 3.
Disc Removal Instructions
(Pedestal sold separately)
®