Intel Pentium D 830 HH80551PG0802MN Data Sheet
Product codes
HH80551PG0802MN
Datasheet
21
Electrical Specifications
5.
775_VR_CONFIG_05A and 775_VR_CONFIG_05B refer to voltage regulator configurations that are defined in the Voltage Regulator Down (VRD)
10.1 Design Guide For Desktop LGA775 Socket.
10.1 Design Guide For Desktop LGA775 Socket.
6.
for the minimum, typical, and maximum V
CC
allowed for a given current. The processor should not be subjected
to any V
CC
and I
CC
combination wherein V
CC
exceeds V
CC
_MAX
for a given current.
7.
These frequencies will operate properly in a system designed for 775_VR_CONFIG_05B processors. The power and I
CC
will be incrementally higher
in this configuration due to the improved loadline and resulting higher V
CC
.
8.
I
CC
_MAX
is based on the V
CC
for details.
9.
I
CC_RESET
is specified while PWRGOOD and RESET# are active.
10.
The current specified is also for AutoHALT State.
11.
I
CC
Stop-Grant and I
CC
Enhanced Halt are specified at V
CC
_MAX
.
12.
These parameters are based on design characterization and are not tested.
13.
The maximum instantaneous current the processor will draw while the thermal control circuit is active as indicated by the assertion of PROCHOT# is
the same as the maximum I
the same as the maximum I
CC
for the processor.
14.
V
TT
must be provided via a separate voltage source and not be connected to V
CC
. This specification is measured at the land.
15.
Baseboard bandwidth is limited to 20 MHz.
16.
This is maximum total current drawn from V
TT
plane by only the processor. This specification does not include the current coming from R
TT
(through
the signal line). Refer to the Voltage Regulator Down (VRD) 10.1 Design Guide For Desktop LGA775 Socket to determine the total I
TT
drawn by the
system.
Table 2-4. V
CC
Static and Transient Tolerance for 775_VR_CONFIG_05A Pentium D Processor
Icc (A)
Voltage Deviation from VID Setting (V)
1, 2, 3
NOTES:
1.
The loadline specification includes both static and transient limits except for overshoot allowed as shown in
2.
This table is intended to aid in reading discrete points on
.
3.
The loadlines specify voltage limits at the die measured at the VCC_SENSE and VSS_SENSE lands. Voltage
regulation feedback for voltage regulator circuits must be taken from processor VCC and VSS lands. Refer to
the Voltage Regulator Down (VRD) 10.1 Design Guide For Desktop LGA775 Socket for socket loadline guide-
lines and VR implementation details.
regulation feedback for voltage regulator circuits must be taken from processor VCC and VSS lands. Refer to
the Voltage Regulator Down (VRD) 10.1 Design Guide For Desktop LGA775 Socket for socket loadline guide-
lines and VR implementation details.
-
Maximum Voltage
1.30 m
Ω
Typical Voltage
1.38 m
Ω
Minimum Voltage
1.45 m
Ω
0
0.000
-0.019
-0.038
5
-0.007
-0.026
-0.045
10
-0.013
-0.033
-0.053
15
-0.020
-0.040
-0.060
20
-0.026
-0.047
-0.067
25
-0.033
-0.053
-0.074
30
-0.039
-0.060
-0.082
35
-0.046
-0.067
-0.089
40
-0.052
-0.074
-0.096
45
-0.059
-0.081
-0.103
50
-0.065
-0.088
-0.111
55
-0.072
-0.095
-0.118
60
-0.078
-0.102
-0.125
65
-0.085
-0.108
-0.132
70
-0.091
-0.115
-0.140
75
-0.098
-0.122
-0.147
80
-0.101
-0.126
-0.151
85
-0.111
-0.136
-0.161
90
-0.117
-0.143
-0.169
95
-0.124
-0.150
-0.176
100
-0.130
-0.157
-0.183