Clarion CZ703E User Manual

English

6

CZ703E

•  New discs may have some roughness 

around the edges. If such discs are used, 

the player may not work or the sound may 

skip. Use a ball-point pen or the like to 

remove any roughness from the edge of 
the disc.

•  Never stick labels on the surface of the disc 

or mark the surface with a pencil or pen.

•  Never play a disc with any cellophane tape 

or other glue on it or with peeling off marks. 

If you try to play such a disc, you may not 

be able to get it back out of the player or it 

may damage the player.

•  Do not use discs that have large scratches, 

are misshapen, cracked, etc. 

  Use of such discs may cause misoperation 

or damage.

•  To remove a disc from its storage case, 

press down on the center of the case and 

lift the disc out, holding it carefully by the 

edges.

•  Do not use commercially available disc 

protection sheets or discs equipped with 

stabilizers, etc. These may damage the 

disc or cause breakdown of the internal 

mechanism.

•  Do not expose discs to direct sunlight or 

any heat source.

•  Do not expose discs to excess humidity or 

dust.

•  Do not expose discs to direct heat from 

heaters.

•  To remove fingermarks and dust, use a soft 

cloth and wipe in a straight line from the 

center of the disc to the circumference.

•  Do not use any solvents, such as 

commercially available cleaners, anti-static 

spray, or thinner to clean discs.

•  After using special disc cleaner, let the disc 

dry off well before playing it.

•  Never turn off the power and remove the 

unit from the car with a disc loaded.

Ball-point pen 

Roughness

•  Refer to the diagrams in “3. CONTROLS” 

when reading this chapter.

•  Start the engine before using this unit.

•  Be careful about using this unit for a long 

time without running the engine. If you 

drain the car’s battery too far, you may not 

be able to start the engine and this can 

reduce the service life of the battery.

1.  Start the engine. The power button / knob 

illumination on the unit will light up.

                 

Engine ON 

position

2.  When power on first time, you can select 

initial speaker system. (Refer to “

”)

  • 

…. When powering on the unit 

for the first time, you can select a speaker 

system. Check your speaker system, 

choose it on the unit, and then, set your 

desired sound quality referring to “

”.

  • 

…. When powering on the unit 

for the first time, “

” is not selected.

   When this unit is turned on for the first 

time, it allows you to select a speaker 

system.

   “

” …. FRONT 2ch / REAR 2ch / 

SUBWOOFER 2ch

   “

” …. HIGH 2ch / MID 2ch / REAR 

2ch

   “

” …. HIGH 2ch / MID 2ch / 

SUBWOOFER 2ch

   If you press the 

 button or 

disconnect the back-up line after 

completing the audio setup, “

 / 

” is displayed. In this case, the unit 

functions as follows.

  • 

 …. When powering on the 

unit after 

 or the backup line is 

disconnected, the audio setup in the 

memory is cleared and you will need to 

start from selecting a speaker system. 

Choose your desirable speaker system 

and set your desired sound quality 

referring to “

”.

  • 

 …. When powering on the 

unit after 

 or the backup line is 

disconnected, the preset speaker system 

and other settings are called.

   If you changed the speaker system, reset 

from 

INITIAL. 

3.  Press the [

SRC /   

] button on the front 

panel or the remote control to turn on the 

power under standby mode. The unit goes 

back to the last status after power on.

4.  Press and hold the [

SRC /   

] button on 

the front panel or the remote control to turn 

off the power.

•   The displayed clock data is based on the 

CT (clock time) data in the RDS signal.

Press the [

] button on the remote 

control to mute the volume from the unit.

Doing the operation above again or adjusting 

volume will release muting.