Tele 110301 Time Delay Relay, Timer, 1 CO contact 230 Vac 110301 Leaflet

ENYA series
Switch-off warning
Retrigger, time extension function programmable
Energy saving function
Impulse switch mode selectable
Low switching noise
High switching capacity, 80A peak inrush current
Automatic 3/4 - wire detection
Push-button glow lamp load up to 100mA
Width 17.5 mm
Installation design

Electronic staircase lighting timer with switch-off warning.

The control input allows the connection of pushbuttons with a total 

glow lamp load up to 100mA and enables the application in 3- or 4-wire 

circuits. The unit can be retriggered via the connected pushbuttons.

A long keypress will switch off the light (energy saving function).

A fast sequence of pushes (pumping) will extend the period to a multiple 

of the selected value. Depending upon distinct type, the following 

operating methods can be selected by the controls on the unit:

 

TW Automatic timer with switch-off warning

 

T  Automatic timer without switch-off warning

 

1  Steady light (ON)

 

0  Switch-off

 

P  Impulse switch mode without time function (only types with option P)

 

PN  Impulse switch mode power fail latch (only types with option PN)

Function sets on distinct types are according to table ordering 

information or printing on the unit.

Adjustment range

Time  0,5 - 12min (in function T, TW)

Green LED U ON:   

indication of supply voltage

Yellow LED ON/OFF:  

indication of relay output

Self-extinguishing plastic housing, IP rating IP 40

Mounted on DIN-rail TS 35 according to EN 60715

Mounting position: any

Shockproof terminal connection according to VBG 4 (PZ1 required), 

IP rating IP20

Tightening torque: max. 1Nm

Terminal capacity:

 

1 x 0.5 to 2.5mm² with/without multicore cable end

 

1 x 4mm² without multicore cable end

 

2 x 0.5 to 1.5mm² with/without multicore cable end

 

2 x 2.5mm² flexible without multicore cable end

Supply voltage:   

 

terminals L - N

Nominal voltage:  

 

see table ordering information or 

 

 

 

 

 

 

printing on the unit

Tolerance:   

 

 

-15% to +10%

Rated consumption:   

2VA (1,0W)

Rated frequency: 

 

AC 48 to 63Hz

Duty cycle:   

 

 

100%

Reset time:   

 

 

500ms

Hold-up time: 

 

 

-

Residual ripple for DC:  -

Drop out voltage: 

 

>30%

Overvoltage category:  III (in accordance with IEC 60664-1)

Rated surge voltage:  

4kV

1 normally open contact  terminals L - 18

Rated voltage:   

 

 

250V AC

Switching capacity:   

 

10A continuous current

If the distance between the devices is less than 5mm!

Switching capacity:   

 

16A continuous current

If the distance between the devices is greater than 5mm!

Start-up peak (20ms): 

 

80A

Mechanical life:   

 

 

30 x 10

6

 operations

Electrical life  

 

 

 

Resistive load:   

 

 

10

5

 operations at 16A 250V

Lamp load:   

 

 

 

80.000 operations at 1000W 250V

Connection not potential free: pushbutton B1-N (3-conductor circuit)

 

 

 

 

 

 

 

pushbutton B1-L (4-conductor circuit)

Glow lamp load:  

 

 

max. 100mA parallel to the pushbuttons

Overload prodection:  

 

yes, electronic

Connection:  

 

 

 

control voltage on terminals C1(+)-C2

Voltage range:   

 

 

8 ... 230V AC/DC

Galvanic isolation:   

 

yes, basic isolation

Overvoltage category:   

III (in accordance with IEC 60664-1)

Rated surge voltage:  

 

4kV

Base accuracy:   

 

 

±5% of maximum scale value

Adjustment accuracy: 

 

<15% of maximum scale value

Repedition accuracy:  

 

<2% 

Voltage influence:   

 

-

Temperature influence:   

≤1%

Ambient temperature: 

 

-25 to +55°C 

Storage temperature: 

 

-25 to +70°C

Transport temperature:   

-25 to +70°C

Relative humidity:   

 

15% to 85%

 

 

 

 

 

 

 

(in accordance with IEC 60721-3-3

 

 

 

 

 

 

 

class 3K3)

Pollution degree:  

 

 

2, if built-in 3

 

 

 

 

 

 

 

(in accordance with IEC 60664-1)

Single packing:   

 

 

106g