MEAN WELL LED driverLED-switching power supply LCM-60 LCM-60 Data Sheet

2 ~ 90V

2 ~ 86V

2 ~ 90V

2 ~ 67V

2 ~ 57V

2 ~ 42V

60.3W
±5%

700mVp-p

95V

73V

500ms, 80ms / 230VAC at rated power

180 ~ 295VAC          254 ~ 417VDC

47 ~ 63Hz

Total harmonic distortion will be lower than 20% when output loading is 75% or higher

92%

<0.5mA / 240VAC

Compliance to EN55015, EN61000-3-2 Class C(

40% rated power) ; EN61000-3-3

≧

Compliance to EN61000-4-2,3,4,5,6,8,11, EN55024, EN61547 light industry level (surge 2KV),  criteria A

-30 ~ +60

 (Refer to "Derating Curve")

℃

20 ~ 90% RH non-condensing

-40 ~ +80

, 10 ~ 95% RH

℃

±

℃

℃

0.03%/

 (0 ~ 50

)

10 ~ 500Hz, 2G 10min./1cycle, period for  60min. each along X, Y, Z axes

260.6K hrs min.      MIL-HDBK-217F (25

)

℃

123.5*81.5*23mm (L*W*H)

1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25  of ambient temperature.

℃

2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf parallel capacitor.
3. Please see "DIP switch table".
4. Derating may be needed under low input voltage. Please check the static characteristics for more details.
5. Length of set up time is measured at first cold start. Turning ON/OFF the power supply may lead to increase of the set up time.
6. Efficiency is measured at 900mA/67V output set by DIP switch.
7. No load power consumption<1W is measured at 180 277VAC, with lighting fixture connected and output current dimmed to 0%.

~

8. The power supply is considered as a component that will be operated in combination with final equipment. Since EMC performance will be affected by the 
    complete installation, the final equipment manufacturers must re-qualify EMC Directive on the complete installation again.
9. To fulfill requirements of the latest ErP regulation for lighting fixtures, this LED power supply can only be used behind a switch without permanently 
    connected to the mains.

0.24Kg ; 54pcs/15Kg/1.12CUFT

60W Multiple-Stage Output Current LED Power Supply

‧

Output current level selectable by DIP S.W.

‧

180~295VAC input only

‧

Built-in active PFC function

‧

Protections: Short circuit / Over voltage / Over temperature

‧

Cooling by free air convection

‧

Fully isolated plastic case

‧

Class   power unit, no FG

Ⅱ

‧

Built-in 0~10Vdc and PWM signal dimming function

‧

Built-in 12V/50mA auxiliary output

‧

Logarithm or linear dimming curve selectable(Meet IEC62386-207)

‧

Temperature compensation function by external NTC

‧

No load power consumption <1W(Note.7)

‧

Power supplies synchronization function up to 10 units

‧

Suitable for indoor LED lighting applications

‧

3 years warranty

■

 Features :

16ms/230VAC at rated power

I/P-O/P:3.75KVAC

UL8750, ENEC EN61347-1, EN61347-2-13, EN62384 independent approved 

I/P-O/P:>100M Ohms / 500VDC / 25

/ 70% RH

℃

500mA

700mA

600mA

900mA

1050mA

1400mA

±5.0%

Constant current limiting, recovers automatically after fault condition is removed

Protection type : Shutdown o/p voltage, re-power on to recover

105 ~ 125V

Shut down o/p voltage, re-power on to recover

12V @ 50mA for driving fan; Tolerance

5%

±

By external NTC(not provide with the power supply), please see "Temperature Compensation Operation"

Please see "Synchronization Operation"

Please see "Dimming Operation"

0.32A/230VAC          0.27A/277VAC

PF

0.975/230VAC, PF

0.96/277VAC at rated power  (Please refer to "Power Factor Characteristic" curve)

≧

≧

COLD START 20A(t

=270  s measured at 50% I

) at 230VAC 

width

peak

μ