Finder 67.23.9.005.4300 PCB Mount Relay 67.23.9.005.4300 Data Sheet
Product codes
67.23.9.005.4300
67.22-4300
67.23-4300
1
2 NO (DPST-NO)
3 NO (3PST-NO)
≥ 3
≥ 3
50/150
50/150
400/690
400/690
20,000
20,000
2,300
2,300
2
2
—
7
50/4/1
50/4/1
1,000 (10/10)
1,000 (10/10)
AgSnO
2
AgSnO
2
5 - 6 - 8 - 12 - 24 - 48 - 60 - 110
1.7
1.7
(0.90 …1.1) U
N
(0.90 …1.1) U
N
(0.95…2.5) U
N
(0.95…2.5) U
N
(0.32...0.65) U
N
(0.32...0.65) U
N
0.17
0.17
0.05 U
N
0.05 U
N
1 · 10
6
1 · 10
6
30 · 10
3
30 · 10
3
25/5
25/5
–40...+70 (–40...+85)
–40...+70 (–40...+85)
RTII
RTII
Contact specification
Contact configuration
Contact gap
mm
Rated current/Maximum peak current (for 5 ms) A
Rated voltage/Maximum switching voltage V AC
Rated load AC1/AC7a (per pole)
VA
Rated load AC15 (per pole @ 230 V AC) VA
Single-phase motor rating (230 V AC)
kW
Three-phase motor rating (480 V AC)
kW
Breaking capacity DC1: 24/110/220 V
A
Minimum switching load
mW (V/mA)
Standard contact material
Coil specification
Nominal voltage (U
N
)
V DC
Rated power
W
Operating range (–40…+70°C)
DC
Energy-saving mode (–40...+85)°C
Operating range for 1s
Holding voltage range
DC
Minimum holding power
W
Must drop-out voltage
DC
Technical data
Mechanical life
cycles
Electrical life at rated load AC7a
cycles
Operate/release time
ms
Ambient temperature range (energy-saving mode) °C
Environmental protection
Approvals (according to type)
Copper side view
Copper side view
•
2 NO
•
Contact gap ≥ 3 mm
•
PCB mount
Features
Printed circuit mount - 3 mm contact gap
50 A Power relay for photovoltaic inverters
50 A Power relay for photovoltaic inverters
•
2 and 3 pole versions
(NO, double break contacts)
(NO, double break contacts)
•
Contact gap ≥ 3 mm (according to
VDE 0126-1-1, EN 62109-1, EN 62109-2)
VDE 0126-1-1, EN 62109-1, EN 62109-2)
•
DC coils, with only 170 mW holding power
•
Reinforced insulation between coil and contacts
•
1.5 mm gap between PCB and relay base
•
Suitable for use at ambient temperatures up to
85 °C (with energy-saving coil energization)
or 70 °C (with standard coil energization)
85 °C (with energy-saving coil energization)
or 70 °C (with standard coil energization)
•
Meets the EN 60335-1 requirements of
resistance to heat and fire (GWIT 775 °C and
GWFI 850 °C)
resistance to heat and fire (GWIT 775 °C and
GWFI 850 °C)
•
3 NO
•
Contact gap ≥ 3 mm
•
PCB mount
For outline drawing see page 6
II-2014, www
.finder
net.com
A
67 Series - Solar relay 50 A
67
SERIES