Slv Tristan 160864 G13 Silver-grey 160864 User Manual
Product codes
160864
2. Technical Data:
160761/64 160841/44 160851/54 160861/64
Operating voltage:
230V ~50Hz
Safety class:
I
Bulb:
2x T8(T26),
G13, 36W
G13, 36W
2x T8(T26),
G13, 18W
G13, 18W
2x TC-L
2G11, 18W
2G11, 18W
2x T8(T26)
G13, 58W
G13, 58W
Dimensions cm
(L/W/H):
(L/W/H):
131,5/
18,5/6,2
70,5/
18,5/6,2
34/
18,5/6,2
161/
18,5/6,2
Weight:
4,00 kg
2,30 kg
1,5 kg
5,3 kg
Importer:
SLV Elektronik GmbH
3. Installation
The electric connection may be executed only by an electric expert
who is familiar with the valid directives!
Attention: Switch off the power of the mains supply line or
respectively of the connection lead before doing any works
.
Use only
parts, which are supplied with the product or are described as accessories!
Otherwise the product or the installation might not be sufficiently safe.
Installation place:
The product is suited for ceiling installation.
Make sure that the product is mounted on a stable, even and tilt-fixed
background.
The light exit should be placed at least so far from the illuminated surface,
as indicated as minimum distance on the type plate of the luminaire:
Otherwise the product or the installation might not be sufficiently safe.
Installation place:
The product is suited for ceiling installation.
Make sure that the product is mounted on a stable, even and tilt-fixed
background.
The light exit should be placed at least so far from the illuminated surface,
as indicated as minimum distance on the type plate of the luminaire:
. Pay special caution to easily inflammable objects (e.g.
curtains).
Separate Installation Steps
Carefully take the screens off the fixture (1).
With a quarter-turn the plastic retainer are loosened to remove the
Separate Installation Steps
Carefully take the screens off the fixture (1).
With a quarter-turn the plastic retainer are loosened to remove the
reflector (2).
Mark and drill the fastening holes corresponding to the holes on the
backside
of the fixture. Note the position of the cable inlet. Do not damage the
power supply line in the, i.e. by drilling, screws or strong bending. This
can lead to a short circuit.
can lead to a short circuit.
Direct the power supply cable through the rubber gasket into the fixture
(3).
Fasten the fixture to the ceiling using properly dimensioned fastening
materials (4).
Electrical Connection (5)
The product must be able to be separated by an all pole separation from
The product must be able to be separated by an all pole separation from
the current supply.
For electric connection attach the black or brown wire (live conductor) of
the mains supply with the clamp L and the blue wire (neutral conductor)
of the mains supply with the clamp N. The green-yellow wire (protective
conductor) of the mains supply has to be tightly screwed into the earth
of the mains supply with the clamp N. The green-yellow wire (protective
conductor) of the mains supply has to be tightly screwed into the earth
clamp
of the product.
Fasten the reflector back to the fixture using the two plastic retainer (6).
Place the tubes into the fixture. T8: Insert the fluorescent tube into the
Place the tubes into the fixture. T8: Insert the fluorescent tube into the
recesses of the sockets. With a quarter-turn the bulb is fixed. TC-L: Stick
the bulb into the socket.
the bulb into the socket.
Put the screens back on. (7)
Ensure that the light fixture holds securely!
The product is now ready for operation.
Ensure that the light fixture holds securely!
The product is now ready for operation.
4. Operation
:
Information for the user:
Operate the product only if it is working correctly. Switch off the product
with a malfunction immediately and operate it again only after examination
by an electrical specialist. This is the case, when:
visible damages appear.
the product does not work.
smoke, steam or crackling sounds appear.
an overheating is recognisable.
Repairs of the product or work on mains voltage-prominent sections may
only be carried out by qualified electricians.
an overheating is recognisable.
Repairs of the product or work on mains voltage-prominent sections may
only be carried out by qualified electricians.
Attention: Here exists mortal danger from an electric shock!
How to avoid failure and fire risk:
Do not cover the product - provide free air circulation!
Do not hang or fasten anything on the product, especially no decoration.
Do not cover the product - provide free air circulation!
Do not hang or fasten anything on the product, especially no decoration.
Never let children play unsupervised with electric products! Children
can not always estimate dangers in dealing with electric energy correctly.
What is to do if a bulb is defect or does not work?
Disconnect the product from power, before you exchange the bulbs.
Disconnect the product from power, before you exchange the bulbs.
Caution: Let the bulb cool down first before replacement – otherwise
considerable risk of injury exists because of the hot surface.
Replace the bulbs only with bulbs of the same data like socket, power
and capacity. Every other sort of bulb can lead to damages of the light.
Replacing the bulb: see Installation.
5. What else has to be considered?
Disconnect the product from power, before you…
clean or maintain the product.
do any works on the product or its components (electric expert).
clean or maintain the product.
do any works on the product or its components (electric expert).
1. A utiliser comme indiqué :
Ce produit ne sert qu’à éclairer:
il est prévu pour une tension de 230V ~50Hz.
il peut uniquement être utilisé dans un endroit sec et surtout pas :
il est prévu pour une tension de 230V ~50Hz.
il peut uniquement être utilisé dans un endroit sec et surtout pas :
dans un environnement poussièreux ou humide
dans un environnement d'air humide
dans un environnement d'air humide
il ne doit être soumis ni aux efforts mécaniques importants ni à un
encrassement important.
il ne doit être utilisé qu’après examen si le produit a été stocké dans un
entrepôt humide ou sale.
il ne doit pas être modifié.
Un non-respect de ces points peut causer un court-circuit ou une
décharge électrique!
2. Informations techniques:
160761/64 160841/44 160851/54 160861/64
Tension
d'alimentation:
d'alimentation:
230V ~50Hz
Classe de
protection:
protection:
I
Ampoule:
2x T8(T26),
G13, 36W
G13, 36W
2x T8(T26),
G13, 18W
G13, 18W
2x TC-L
2G11, 18W
2G11, 18W
2x T8(T26)
G13, 58W
G13, 58W
Dimensions cm
(L/L/H):
(L/L/H):
131,5/
18,5/6,2
70,5/
18,5/6,2
34/
18,5/6,2
161/
18,5/6,2
Poids:
4,00 kg
2,30 kg
1,5 kg
5,3 kg
Importateur:
SLV Elektronik GmbH
3. Installation
La connection électrique doit être exécutée par un professionnel,
lequel est familier des normes en vigueur!
Attention: Mettez l’alimentation électrique ou le raccordement au
secteur hors tension avant de travailler!
Utilisez seulement des pièces qui ont été livrées avec le produit ou qui sont
uniquement décrites comme accessoires ! Sinon, l’installation ainsi que le
produit ne peuvent pas être garantis.
Lieu d'installation
Ce produit est fait pour un montage au plafond. Veillez à ce que le produit
soit monté de manière stable et résistante au basculement.
La distance entre la sortie de lumière et la face illuminée devrait au moins
être tant que la distance minimale indiquée sur l’étiquette du type du
Utilisez seulement des pièces qui ont été livrées avec le produit ou qui sont
uniquement décrites comme accessoires ! Sinon, l’installation ainsi que le
produit ne peuvent pas être garantis.
Lieu d'installation
Ce produit est fait pour un montage au plafond. Veillez à ce que le produit
soit monté de manière stable et résistante au basculement.
La distance entre la sortie de lumière et la face illuminée devrait au moins
être tant que la distance minimale indiquée sur l’étiquette du type du
luminaire:
. Soyez prudent avec les matières inflammables
(comme rideaux etc.).
Etapes successives pour installer le luminaire
Enlevez prudemment les trames de la lampe (1).
Enlevez prudemment les deux maintiens en plastique en les tournant
Enlevez prudemment les deux maintiens en plastique en les tournant
d’un quart de tour pour enlever le réflecteur.
Marquez et percez les trous pour la fixation en fonction des trous au dos
de la lampe. Faites attention à la position de l’adduction. Soyez attentif à
ce que le câble d'alimentation ne soit pas endommagé. Dans le cas
contraire, il pourrait causer un court-circuit.
ce que le câble d'alimentation ne soit pas endommagé. Dans le cas
contraire, il pourrait causer un court-circuit.
Passez l’adduction à travers le joint en caoutchouc (3).
Fixez la lampe au plafond avec assez de matériel de fixation
Fixez la lampe au plafond avec assez de matériel de fixation
dimensionné (4).
Raccordement électrique (5):
Ce système doit pouvoir être coupé du réseau individuellement.
Pour réaliser le raccordement électrique, connectez le fil électrique noir
Ce système doit pouvoir être coupé du réseau individuellement.
Pour réaliser le raccordement électrique, connectez le fil électrique noir
ou brun (la phase) du réseau électrique à la borne L et le fil électrique
bleu (fil neutre) du réseau électrique à la borne N. Le fil électrique vert
bleu (fil neutre) du réseau électrique à la borne N. Le fil électrique vert
F
Mode d'emploi TRISTAN
160761/64 160841/44/51/54/61/64 07/2007
© by SLV
Elektronik GmbH
Technical Details are subject to change.
Technical Details are subject to change.
Duplication prohibited !
2
2
6
4
4
7
5
3
1
7
1
6
L
N