Briloner Indoor panel mounted lamp 7134-611 Aluminium 7134-611 User Manual
Product codes
7134-611
Sicherheitshinweise / Bitte lesen Sie diese Informationen sorgfältig durch, bevor Sie mit der Installation oder Inbetriebnahme dieses
Produkts beginnen. Heben Sie diese Gebrauchsanweisung für spätere Zwecke gut auf.
1. Die Leuchten dürfen nur von autorisiertem Fachpersonal nach den jeweils geltenden Elektro- Installationsvorschriften installiert werden.
2. Der Hersteller übernimmt keine Verantwortung für Verletzungen oder Schäden, die Folge eines unsachgemäßen Gebrauchs der Leuchte sind.
3. Die Pflege von Leuchten beschränkt sich auf die Oberflächen. Dabei darf keine Feuchtigkeit in Anschlussräume oder an Netzspannung führende
2. Der Hersteller übernimmt keine Verantwortung für Verletzungen oder Schäden, die Folge eines unsachgemäßen Gebrauchs der Leuchte sind.
3. Die Pflege von Leuchten beschränkt sich auf die Oberflächen. Dabei darf keine Feuchtigkeit in Anschlussräume oder an Netzspannung führende
Teile gelangen.
4. Achtung! Vor Beginn der Montagearbeiten die Netzleitung spannungsfrei schalten – Sicherungsautomat ausschalten bzw. Sicherung heraus drehen.
Schalter auf “AUS”.
5. Die Leuchte besitzt den Schutzgrad “IP44“ und ist ausschließlich für den Einsatz im Innenbereich von privaten Haushalten vorgesehen.
6.
6.
Das Symbol der durchgestrichenen Mülltonne auf dem Produkt oder der Verpackung bedeutet, dass dieses Produkt nicht mit dem Hausmüll
entsorgt werden darf. Das Produkt muss stattdessen am Ende seiner Lebensdauer zu einer Annahmestelle für das Recycling von elektrischen und
elektronischen Geräten gebracht werden. Bitte erfragen Sie diese Stelle bei Ihrer zuständigen kommunalen Verwaltung.
elektronischen Geräten gebracht werden. Bitte erfragen Sie diese Stelle bei Ihrer zuständigen kommunalen Verwaltung.
7. Leuchte nicht auf feuchtem oder leitendem Untergrund montieren.
8. Stellen Sie sicher, dass Leitungen bei der Montage nicht beschädigt werden.
9. Anschlussart Typ Y: Zur Vermeidung von Gefährdungen darf eine beschädigte äußere flexible Leitung dieser Leuchte ausschließlich vom
8. Stellen Sie sicher, dass Leitungen bei der Montage nicht beschädigt werden.
9. Anschlussart Typ Y: Zur Vermeidung von Gefährdungen darf eine beschädigte äußere flexible Leitung dieser Leuchte ausschließlich vom
Hersteller, seinem Servicevertreter oder einer vergleichbaren Fachkraft ausgetauscht werden.
10. Achtung! Leuchtenteile und Leuchtmittel können während des Betriebs Temperaturen von >70°C erreichen und dürfen daher während des Betriebs
nicht berührt werden.
11. Nicht direkt in die Lichtquelle (Leuchtmittel, LED etc.) hineinschauen.
12. Das Leuchtmittel ist nicht austauschbar
13. Es dürfen nur Netzgeräte verwendet werden, die nach DIN EN61347-2-13 zugelassen sind.
Verehrter Kunde
Sollten sich trotz neuster Fabrikationsmethoden und genauesten Qualitätskontrollen wider Erwarten Mängel herausstellen, wenden Sie sich bitte unter
Angabe des Kaufdatums, des Kaufortes und der Artikelnummer des Produktes an folgende kostenlose Hotline: 00800/BRILONER (00800/27456637)
12. Das Leuchtmittel ist nicht austauschbar
13. Es dürfen nur Netzgeräte verwendet werden, die nach DIN EN61347-2-13 zugelassen sind.
Verehrter Kunde
Sollten sich trotz neuster Fabrikationsmethoden und genauesten Qualitätskontrollen wider Erwarten Mängel herausstellen, wenden Sie sich bitte unter
Angabe des Kaufdatums, des Kaufortes und der Artikelnummer des Produktes an folgende kostenlose Hotline: 00800/BRILONER (00800/27456637)
Safety directions / Please read this information carefully before installing or using this product. Please keep this user manual for further
reference.
1. The lamps may only be installed by authorized and qualified technicians according the valid regulations for electrical installation.
2. The manufacturer does not accept any responsibility for injuries or damage resulting from improper use of the light.
3. Maintenance of the lights is limited to the surfaces. When doing this, no moisture must come into contact with any areas of the terminal connections
2. The manufacturer does not accept any responsibility for injuries or damage resulting from improper use of the light.
3. Maintenance of the lights is limited to the surfaces. When doing this, no moisture must come into contact with any areas of the terminal connections
or mains voltage control parts.
4. Attention! Before starting the installation work, make sure that the mains power line is voltage-free – turn off safety cutout or unscrew the
protection fuse. The switch must be “OFF”.
5. The lights have a protection class rating of “IP44“ and are solely intended for use in interior areas of private households.
6.
6.
The symbol of the crossed-out garbage can on the product or the packaging means that the product must not be disposed with ordinary household
waste. At the end of its useful life, the product must be returned to a point of acceptance for the recycling of electric and electronic device. Please
ask your local municipality for the point of acceptance.
ask your local municipality for the point of acceptance.
7. Do not install the light on a damp or conductive subsurface.
8. Please make sure that no cables get damaged during the installation work.
9. Connection type Y: In order to eliminate any risks in case of damages, the extremely flexible cable of this lamp may only be replaced by a special
8. Please make sure that no cables get damaged during the installation work.
9. Connection type Y: In order to eliminate any risks in case of damages, the extremely flexible cable of this lamp may only be replaced by a special
cable or by a cable exclusively available from the manufacturer, its service representative or a comparable qualified technician.
10. Attention! During operation, lamp parts and illuminants can reach temperatures of more than 70°C. Do not touch during operation!
11. Do not look directly into the light source (illuminant, LED, etc.).
12. The illuminant can not be replaced.
13. Only use power supplies that are approved and conform with DIN EN61347-2-13.
11. Do not look directly into the light source (illuminant, LED, etc.).
12. The illuminant can not be replaced.
13. Only use power supplies that are approved and conform with DIN EN61347-2-13.
Consignes de sécurité / Merci de lire ces informations avec attention avant de commencer avec l’installation ou la mise en marche de ce
produit. Conservez ce mode d’emploi pour pouvoir le consulter plus tard en cas de besoin.
1. Les lampes doivent être installées par un personnel spécialisé uniquement, en suivant les instructions d’installation électronique en vigueur.
2. Le fabricant n’est pas responsable des blessures ou des dommages résultant d’une utilisation incorrecte des lampes.
3. Le soin des lampes se limite aux surfaces. Il faut absolument éviter de mettre le secteur de branchements ou la tension du réseau des pièces
2. Le fabricant n’est pas responsable des blessures ou des dommages résultant d’une utilisation incorrecte des lampes.
3. Le soin des lampes se limite aux surfaces. Il faut absolument éviter de mettre le secteur de branchements ou la tension du réseau des pièces
conductrices en contact avec l’humidité.
4. Attention! Avant de commencer les travaux de montage, éteindre la tension du cordon d’alimentation– éteindre le disjoncteur ou dévisser les
fusibles. Placer le commutateur sur „OFF“.
5. Le luminaire possède le degré de protection "IP44" et est exclusivement réservé à une utilisation dans la partie intérieure de domiciles privés.
6.
6.
Le symbole du bidon d'ordures rayé sur le produit ou l'empaquetage signifie que le produit ne doit pas être disposé avec le déchet ordinaire de
ménage. À la fin de son vie utile, le produit doit être retourné à un point d'acceptation pour la réutilisation des appareils électroniques ou électriques.
Veuillez demander votre municipalité locale pour le point d'acceptation.
Veuillez demander votre municipalité locale pour le point d'acceptation.
7. Ne pas monter la lampe sur un support humide ou conducteur.
8. Veuillez vous assurer que les cordons ne soient pas abîmés pendant le montage.
9. Type de connexion Y: afin d’éviter tout danger un fil abîmé extérieurement ne peut être remplacé que par le fabricant, le revendeur officiel ou un
8. Veuillez vous assurer que les cordons ne soient pas abîmés pendant le montage.
9. Type de connexion Y: afin d’éviter tout danger un fil abîmé extérieurement ne peut être remplacé que par le fabricant, le revendeur officiel ou un
technicien spécialisé.
10. Attention! Les parties de la lampe et les parties qui éclairent peuvent atteindre des températures supérieures à 70°C pendant leur fonctionnement, et
ne doivent donc pas être touchées pendant leur fonctionnement.
11. Ne regardez pas directement la source lumineuse (illuminant, LED, etc.).
12. Le système d’éclairage n’est pas échangeable
13. Utiliser uniquement des blocs d’alimentation homologués conformément à DIN EN61347-2-13.
Revision 00_07/2013
12. Le système d’éclairage n’est pas échangeable
13. Utiliser uniquement des blocs d’alimentation homologués conformément à DIN EN61347-2-13.
Revision 00_07/2013
MAL 7135_7136_7139_7140
Montageanleitung
Montasjeveiledning
Szerelési utasítás
Mounting instruktiones
Asennusohje
Instruc
ţiunile de montaj
Instruction de montage
Montageaanwijzing
Instruções de montagem
Istrutione di montaggio
Instrukja monta
żu
Montaj talimati
Instrucciones de montaje
Návod k montáži
Mont
āžas instrukcija
Montageanledning
Návod na použitie
Рьководство за монтаж
Monteringsinstruktion
Montazno navodilo
Инструкция по монтажу
Συναρµολογησησ
MAL 7135_7136_7139_7140 Page1a
IP44