Aerotec 2009534 Data Sheet
Always keep the machine in perfect condition. Observe
the operating instructions for the cleaning, lubricating
and changing of accessories.
Always disconnect the machine from the compressed
air supply before starting maintenance work or the
changing of accessories is to be carried out. To do so,
close the valve (18) and open the valve (12). Wait until
the indicator on the pressure gauge (15) shows zero.
Only use recommended accessories. In addition,
observe the information in the operating instructions.
The use of unsuitable accessories entails the risk of
accidents.
Avoid the unintentional starting up of the machine.
Always check before connecting to the compressed
air supply that the operating switch of the compressor
is set to OFF AND that the pressure vessel of the
compressor is not under pressure.
Operate the machine at an air pressure between 5
and maximum 8.5 bar! The machine can be damaged
at higher pressures! Personnel may also be put at
risk.
For all interruptions to work, the machine must,
without fail, be separated from the compressed air
supply by disconnection! Otherwise the machine can
be unintentionally started up!!
Before starting work, ALWAYS ensure that all
compressed air connections are intact and in perfect
working order. Otherwise, the connections can
become loose and flying objects (for example,
compressed air hoses) can cause considerable injury
and damage!
Also ensure that the spray nozzle is always closed
when you are not actually holding the spray gun and
working with it.
Check the hoses and other connections for tightness
before every use.
Only use the machine in well ventilated rooms and
ensure that no substances or fumes which are
injurious to health are inhaled.
Smoking in the immediate vicinity of the machine is
strictly forbidden!
Never operate or store the machine close to sources
of heat, open fires or in areas where there may be
sparks!
Never direct the sand stream at people or animals!
the operating instructions for the cleaning, lubricating
and changing of accessories.
Always disconnect the machine from the compressed
air supply before starting maintenance work or the
changing of accessories is to be carried out. To do so,
close the valve (18) and open the valve (12). Wait until
the indicator on the pressure gauge (15) shows zero.
Only use recommended accessories. In addition,
observe the information in the operating instructions.
The use of unsuitable accessories entails the risk of
accidents.
Avoid the unintentional starting up of the machine.
Always check before connecting to the compressed
air supply that the operating switch of the compressor
is set to OFF AND that the pressure vessel of the
compressor is not under pressure.
Operate the machine at an air pressure between 5
and maximum 8.5 bar! The machine can be damaged
at higher pressures! Personnel may also be put at
risk.
For all interruptions to work, the machine must,
without fail, be separated from the compressed air
supply by disconnection! Otherwise the machine can
be unintentionally started up!!
Before starting work, ALWAYS ensure that all
compressed air connections are intact and in perfect
working order. Otherwise, the connections can
become loose and flying objects (for example,
compressed air hoses) can cause considerable injury
and damage!
Also ensure that the spray nozzle is always closed
when you are not actually holding the spray gun and
working with it.
Check the hoses and other connections for tightness
before every use.
Only use the machine in well ventilated rooms and
ensure that no substances or fumes which are
injurious to health are inhaled.
Smoking in the immediate vicinity of the machine is
strictly forbidden!
Never operate or store the machine close to sources
of heat, open fires or in areas where there may be
sparks!
Never direct the sand stream at people or animals!
5. Correct and Proper use
Only use the machine for the sand blasting of fixed
objects. Never hold these objects with the hand or
allow them to be held by other people as this is
extremely dangerous!
Use for all other purposes is considered to be
improper use!
A precondition for the use of the machine is the
reading and understanding of the provisions of these
instructions.
Only use the machine for the sand blasting of fixed
objects. Never hold these objects with the hand or
allow them to be held by other people as this is
extremely dangerous!
Use for all other purposes is considered to be
improper use!
A precondition for the use of the machine is the
reading and understanding of the provisions of these
instructions.
The manufacturer cannot be held responsible for any
injury or damage arising from the non-observance of
the general, applicable Regulations or the provisions
contained in these instructions.
6. Requirements on the Operator
The operator must have carefully read the operating
instructions before using the machine.
With the exception of detailed instruction from a
qualified person, no special qualifications are
necessary for the operation of the machine.
The machine may only be operated by people who
have reached the age of 16. An exception to this is
when the use by a young person is carried out in the
course of the completion of professional training and
under the supervision of an instructor.
The use of the machine simply requires appropriate
instruction. No special training is necessary.
7. Transport and Storage
Store the machine in a clean, dry location and
protect it against unauthorized access.
8. Use of the Sand Blasting Machine
Assembly:
Use exclusively the named components in the scope
of supply.
Assemble the machine in accordance with the
illustration on Page 2. In doing so, ensure that all
connections are sealed. For this, use Teflon tape or
the gaskets supplied with the machine.
In order to test the leak-tightness of the system, we
urgently recommend the filling of the machine with
an air pressure of 5 bar (see the pressure indicator).
Thereafter, switch off the compressor. With correct
sealing, there must be no pressure loss and after
approximately 30 minutes the pressure indicator
should be still showing 5 bar.
injury or damage arising from the non-observance of
the general, applicable Regulations or the provisions
contained in these instructions.
6. Requirements on the Operator
The operator must have carefully read the operating
instructions before using the machine.
With the exception of detailed instruction from a
qualified person, no special qualifications are
necessary for the operation of the machine.
The machine may only be operated by people who
have reached the age of 16. An exception to this is
when the use by a young person is carried out in the
course of the completion of professional training and
under the supervision of an instructor.
The use of the machine simply requires appropriate
instruction. No special training is necessary.
7. Transport and Storage
Store the machine in a clean, dry location and
protect it against unauthorized access.
8. Use of the Sand Blasting Machine
Assembly:
Use exclusively the named components in the scope
of supply.
Assemble the machine in accordance with the
illustration on Page 2. In doing so, ensure that all
connections are sealed. For this, use Teflon tape or
the gaskets supplied with the machine.
In order to test the leak-tightness of the system, we
urgently recommend the filling of the machine with
an air pressure of 5 bar (see the pressure indicator).
Thereafter, switch off the compressor. With correct
sealing, there must be no pressure loss and after
approximately 30 minutes the pressure indicator
should be still showing 5 bar.