Lappkabel 2170232 Interface Cable 2 x 1.5 mm² Red 2170232 Data Sheet
Product codes
2170232
U.I. Lapp
GmbH
DATA SHEET
UNITRONIC BUS AS-INTERFACE (TPE)
DB2170230
valid from: 16.05.2012
Originator: RAWE/PDC
approved: HAPF/PDC
Document:
DB2170230
page 1 of 1
All rights reserved acc. to DIN ISO 16016.
PD 0019/2.2_11.10DE
PD 0019/2.2_11.10DE
Application
Field bus cable for AS-Interface (actuator-sensor interface) networking system for the lower field area. Data transmission for
AS-Interface telegrams and power supply for AS-I slaves, master, repeater, extender and sensors is done via this un-
screened, geometrically-coded two-core flat cable. The contacting of the conductors by the insulation-displacement-system
of the AS-I modules is possible without stripping the insulation.
The oil-resistant outer sheath of this field bus cable recommends its use in typical industrial environment, especially in wet
areas of automotive industry and machining centers in combination with water-based and water-mixable cooling lubricants.
The cable is intended for flexible application and permanent installation in dry and damp interiors.
AS-Interface telegrams and power supply for AS-I slaves, master, repeater, extender and sensors is done via this un-
screened, geometrically-coded two-core flat cable. The contacting of the conductors by the insulation-displacement-system
of the AS-I modules is possible without stripping the insulation.
The oil-resistant outer sheath of this field bus cable recommends its use in typical industrial environment, especially in wet
areas of automotive industry and machining centers in combination with water-based and water-mixable cooling lubricants.
The cable is intended for flexible application and permanent installation in dry and damp interiors.
Design
Conductor
tinned copper, fine-wire stranded, nom. 1.5 mm
2
acc. to IEC 60228/VDE 0295
(class 6)
Insulation
oil resistant TPE, core nom. 2.5 mm
Core identification code
cores brown and blue
Core assembly
2 cores parallel deviation, the brown core is assembled inline with the leading
edge
edge
Outer sheath
oil resistant TPE, yellow similar to RAL1021 (article number 2170230), black
similar to RAL 9005 (article number 2170231) or red similar to RAL 3000 (article
number 2170232)
similar to RAL 9005 (article number 2170231) or red similar to RAL 3000 (article
number 2170232)
Electrical properties at 20° C
Resistance (loop)
max. 27.4 Ω/km
Insulation resistance
min. 10 GΩxcm
Mutual capacitance
max. 80 nF/km
Inductance
0.5 mH/km up to 0.75 mH/km
Characteristic impedance
70 Ω up to 140 Ω
(at 167 kHz)
(at 167 kHz)
Operating voltage
ca. 30 V (DC)
(230 V (AC) for the red version)
(230 V (AC) for the red version)
Operating peak voltage
300 V (not for power purposes)
Test voltage U
eff.
core/core
2000 V
Mechanical and thermal properties
Minimum bending radius
moved: 16 mm in center line
static: 12 mm in center line
static: 12 mm in center line
Permissible temperature range
moved: -30˚ C up to +85˚ C
static: -40˚ C up to +85˚ C
static: -40˚ C up to +85˚ C
Halogen free
acc. to VDE 0472-815
General requirements
Dangerous and forbidden substances acc. to RoHS directive (2002/95/EG) are
not allowed to the manufacturing.
not allowed to the manufacturing.