Wr Rademacher DuoFern 32160211 Wireless wall-mounted switch Surface-mount Max. range (open field) 100 m 32160211 Data Sheet
Product codes
32160211
1. General safety instructions
3. Incorrect use
Never use the DuoFern radio system and its components for
the remote control of appliances and systems with increased
safety-relevant requirements or where there is an accident
risk. This would require additional safety equipment. Ob-
serve the respective statutory regulations for the installation
of such systems.
IMPORTANT
IMPORTANT
Do not install the DuoFern wall controller outside.
The use of defective equipment can lead
to personal injury and damage to prop-
erty.
Never use defective or damaged equipment.
Please contact our Customer Service depart-
ment in this event .
2. Correct usage
Correct usage
Only use the DuoFern wall controller 3216 02 21 / 3216 02 11
for the remote control of:
◆
Shutters / Blinds
◆
Electrical consumers (for instance lighting)
Operating conditions
◆
Only use the DuoFern wall controller in dry rooms.
◆
The installation and operation of the DuoFern radio sys-
tem and its components (e. g. DuoFern tubular motor
actuator) is only permitted for systems and devices
where a malfunction in the transmitter or receiver
would not cause a danger to personnel or property or
where this risk is already covered by other safety equip-
ment.
4.1 Functional description
Use the DuoFern wall controller to manually operate diverse
DuoFern actuators remotely. To do so, connect the DuoFern
wall controller to the required DuoFern network.
Use the two rocker switches to send manual control com-
Use the two rocker switches to send manual control com-
mands to the connected DuoFern actuators.
A bi-coloured indicator light shows whether the DuoFern
A bi-coloured indicator light shows whether the DuoFern
actuators connected to the wall controller have received and
confirmed the control commands. The indicator light is con-
cealed behind the two rocker switches.
4. General view
Front of the keypad
Left rocker switch
Key 1
Key 3
Right rocker switch
Key 2
Indicator light (red/green LED)
The indicator light is concealed behind the two rocker switches.
Key 4
Rear of the keypad
Battery compartment with cover
Key 5
Use a thin object that is not too sharp to press this key
(for instance a paperclip).
4.2. Two operating modes
1. Tubular motor mode
The following control commands are sent in Tubular
motor mode: UP/STOP/DOWN
NOTE
Every DuoFern actuator reacts to these com-
mands. Please additionally read the operat-
ing instructions for the DuoFern actuator.
2. Lighting/Devices mode
The following control commands are sent per rocker
switch: ON/OFF
NOTE
◆
The DuoFern actuator is in Tubular motor mode when
it leaves the factory.
◆
The individual channels of an actuator can be distributed
to the two rocker switches in Lighting/Devices mode.
◆
Only the DuoFern actuators that support On/Off switch-
ing commands react to the Light/Devices mode (e. g.
the DuoFern universal actuator or the DuoFern socket
actuator.)
4.3 Assignment of control commands to the keys
Key
Tubular motor
mode
Lighting/
Devices
mode
1
OPEN (s)
ON (channel 1)
2
STOP
ON (channel 2)
3
DOWN (t)
OFF (channel 1)
4
STOP
OFF (channel 2)
1 + 2
(5 sec)
Enable wall controller login mode
1 + 4
(5 sec)
Switch over between Tubular motor
mode and Lighting/Devices mode
1 + 5
(5 sec)
Change direction
of rotation
Switch over
between
lighting and
devices function
(channel 1)
2 + 3
(5 sec)
Clear up
2 + 5
(5 sec)
- - -
Switch over
between
lighting and
devices function
(channel 2)
3 + 4
(5 sec)
Enable wall controller log off mode.
5
(10 sec)
Reset
Mounting frame
Keypad
Indicator light
Antenna
4.4 Overview of models with number of con-
trollable groups and DuoFern end devices
trollable groups and DuoFern end devices
6. Finally press the cover frame over the keypad.
Take care that the antenna does not become
caught and damaged. The DuoFern wall con-
troller is now ready for operation.
6. Dismantling
1. Dismantle the wall controller in reverse order.
You must assign the wall controller to every required
DuoFern actuator so that the DuoFern wall controller can
control a DuoFern actuator.
You can login a maximum of 32 DuoFern actuators at the
You can login a maximum of 32 DuoFern actuators at the
wall controller, for instance RolloTron Standard or Comfort
DuoFern; DuoFern actuators (Tubular motor actuator or
universal actuator) etc.
1.
1.
Switch the DuoFern actuator to Login
mode (please refer to the correspon-
ding operating instructions).
2. Switch the wall controller to Login mode.
- To do so, press keys 1 and 2 simultaneously and
hold down for approx. 5 seconds.
3.a The wall controller is in Tubular motor mode
(factory setting)
No further configuration is needed - all of the channels
No further configuration is needed - all of the channels
of an actuator are operated at the same time.
3.b The wall controller is in Lighting/Devices mode.
Every channel of the actuator must be assigned to a
rocker switch. The indicator light will continue to show
orange until all of the channels of an actuator are as-
signed.
Proceed as follows:
Proceed as follows:
- Key 1 to operate the channel with the left
rocker switch.
- Key 2 to operate the channel with the right
- Key 2 to operate the channel with the right
rocker switch.
- Press key 3 or 4 in order not to operate the channel.
NOTE
- Press key 3 or 4 in order not to operate the channel.
NOTE
Refer to the table in chapter 4.3. for the changeover
between Tubular motor mode and Lighting/Devices
mode.
3.c Pay attention to the indicator light:
Green: Login was successful.
Red:
Red:
Login failed.
4. Login the next DuoFern actuator.
7. Login of DuoFern end devices
Item no.
Number of
groups
Max. number
of end devices
3216 02 21
3216 02 11
1
32
1. Perform all of the settings required with the
keypad.
2. Select a suitable installation site.
The installation site should preferably be flat and free
of dust.
3. Pull one of the two protective films from the
double-sided adhesive strip and press the mount-
ing frame onto the adhesive strip.
The mounting frame can also be screwed in place with
The mounting frame can also be screwed in place with
two screws if need be.
4. Pull the second protective film from the double-
sided adhesive strip and press it firmly onto the
base surface.
5. Press the keypad into the mounting frame until it
clicks into place.
NOTE
NOTE
◆
Fit the antenna, as shown in the Figure, to ensure
the best possible reception.
◆
Avoid bending the antenna too far as it could
otherwise break off.
5. Installation procedure
Item no.: 3216 02 21 / 3216 02 11
VBD 563-2 (10.12)
DuoFern Wall Controller
Operating and
installation instructions