TP-LINK TL-WR702N Leaflet
150Mbps Wireless N Nano Router
MODEL NO.
TL-WR702N
Package Contents
QIG
150Mbps Wireless N Nano Router
MODEL NO.
TL-WR702N
Resource CD
Ethernet Cable
TL-WR702N
Quick Installation Guide
7106503716
Enter the Network key( 2), and then
Confirm network key. Click Connect.
If you can see Connected as shown
in the following screen, you’ve
successfully connected to the
wireless network.
For Windows 7
For Windows XP
Click the icon at the bottom
of your desktop. Click refresh
button, and then select the
default SSID( 1). Click Connect.
Click the wireless icon at the
bottom of your desktop. Click
Refresh network list, and then
select the default SSID( 1). Click
Connect.
1
2
3
1
2
3
Enter the Security key( 2). Click OK.
Three Typical Working Modes
Router Mode
Wired Network
Cable
Line
The default operation mode is AP mode. In this mode,
TL-WR702N can convert wired network to wireless network.
As a wireless router, TL-WR702N enables multi-user to share
Internet via DSL/Cable Modem.
AP Mode (
default mode
)
1
2
Instant Wireless Connection
Repeater Mode
TL-WR702N is used to extend the range of wireless signal
of the existing AP or wireless router.
3
Hardware Introduction
LAN/WAN: This port works as LAN in AP/Repeater/ Bridge/Client
mode and as WAN in Router mode.
Reset:It is used to reset the TL-WR702N to its factory defaults.
Indication
TL-WR702N LED:
Status
Solid
It’s powered on but the LAN/WAN port is not
connected.
Flashing Slowly
Flashing Quickly
The LAN/WAN cable is connected but there is
no data being transmitted or received.
The LAN/WAN cable is connected and there is
The LAN/WAN cable is connected and there is
data being transmitted or received.
Step 4: For AP Mode and Router Mode, connect the LAN/WAN port of
Before hardware connection, please write down the
SSID and Password of your TL-WR702N on the label
for later use. Both are case-sensitive.
SSID and Password of your TL-WR702N on the label
for later use. Both are case-sensitive.
(This method is for connecting to the default AP Mode. If you want to configure AP Mode or choose other modes, please skip to Advanced Web Management.)
For more detailed information about
Reset, please refer to
Appendix: Troubleshooting.
Step 3: Plug in standard electrical wall socket directly to power the Router.
Ethernet cable.
SSID: Wireless Network Name of TL-WR702N.
*
Password: Pre-encryption password of TL-WR702N.
*
Hardware Connection
If you can see Connected as shown
in the following screen, you’ve
successfully connected to the
wireless network.
Connect to Network
2
Configure PC
1
Go to Start > Control Panel > View
network status and tasks > Change
adapter settings. Right click Wireless
Network Connection, and select
Properties.
network status and tasks > Change
adapter settings. Right click Wireless
Network Connection, and select
Properties.
Double click Internet Protocol
Version 4 (TCP/IPv4) in the item
list.
Version 4 (TCP/IPv4) in the item
list.
Specify the IP address as 192.168.0.x
(x is from 1 to 253), and the Subnet
mask as 255.255.255.0. Type the
Router’s LAN IP address (the default
IP is 192.168.0.254) into the Default
gateway field. Click OK.
(x is from 1 to 253), and the Subnet
mask as 255.255.255.0. Type the
Router’s LAN IP address (the default
IP is 192.168.0.254) into the Default
gateway field. Click OK.
1
2
3
Advanced Web Management
(Here we take Windows 7 as an example.)
Click the wireless icon at the
bottom of your desktop. Click
refresh button, and then select
the default SSID( 1). Click
Connect.
1
2
3
Enter the Security key( 2).
Click OK.
If you can see Connected as shown
in the following screen, you’ve
successfully connected to the
wireless network.
The default SSID of the network is TP-LINK_xxxxxx which is the SSID on the label.
The pre-encryption function is enabled by default and the default Network key/Security key is the Password on the
label. The password is case-sensitive.
1.
2.
The default SSID of the network is TP-LINK_xxxxxx which is the SSID on the label.
The pre-encryption function is enabled by default and the default Security key is the Password on the label. The
password is case-sensitive.
1.
2.
Reset
LAN/WAN
Power
Power Adapter
USB Cable
Power: This port is used to connect the provided power adapter.
Internet
1
2
4
3
Step 1: Connect one end of the provided USB cable to micro USB port of
TL-WR702N.
Step 2: Connect the other end of the provided USB cable to the power
Step 2: Connect the other end of the provided USB cable to the power
adapter.
For another modes,
TL-WR702N to Internet with an
you can refer to the User Guide in the Resource CD.