Bertazzoni 24 Cooktop 4-Burner Owner's Manual
4
2. Side clearances (Minimum values)
The different side clearances shall be in accordance with the minimum values indicated in the table n.1 and
are shown and in the fig. 1
are shown and in the fig. 1
The cooking surface area is defined as that part of the appliance where cooking normally takes place and
does not include those parts of the appliance containing control knobs.
does not include those parts of the appliance containing control knobs.
Table n.1
Min. Clearances
inches (mm)
Min. Clearances
inches (mm)
L1
18
7/8
”
(480)
L10
22
1
/
2
“ (570)
L2
1
9/16
“ (40)
L11
32“ (813)
L3
3
3/8
“ (86)
W
23
1/4
“ (590)
L4
18” (457)
D
19
2/3
“ (500)
L5
24” (610)
B1 (*)
1
3/8
“ (35)
L6
13” (330)
B2 (*)
3
1
/
2
“ (90)
L7
23
1/4
“ (590)
B3 (*)
3” (76)
L8
3/4
“ (20)
B4 (*)
3
1
/
2
“ (90)
L9
3
15/16
” (100) R
5
1/8
“(135)
(*) Note:
-B1 is the min. clearance between the front edge of the appliance and the front edge of the cabinet.
-B2 and B4 are the min. clearance between the left/right side edge of the appliance and the side wall (if
present).
-B3 is the min. clearance between the back edge of the appliance and the back wall.
-B1 is the min. clearance between the front edge of the appliance and the front edge of the cabinet.
-B2 and B4 are the min. clearance between the left/right side edge of the appliance and the side wall (if
present).
-B3 is the min. clearance between the back edge of the appliance and the back wall.
Attaching the hotplate
To prevent liquids from leaking accidentally into the underlying storage space, the appliance is equipped with
a special gasket. To apply this gasket, carefully follow the instructions in Fig. 3. Lay out the protective sealing
strips along the edges of the opening in the bench top and carefully overlap the strip end. (See Fig. 3). insert
the hotplate into the bench top opening. With a screwdriver assemble the brackets A to the hotplate bottom
by means of the screws B. (See Fig. 4). Slide the hooks into position and secure them with the screws.
Trim the part of the sealing strips which extend beyond the hotplate base
a special gasket. To apply this gasket, carefully follow the instructions in Fig. 3. Lay out the protective sealing
strips along the edges of the opening in the bench top and carefully overlap the strip end. (See Fig. 3). insert
the hotplate into the bench top opening. With a screwdriver assemble the brackets A to the hotplate bottom
by means of the screws B. (See Fig. 4). Slide the hooks into position and secure them with the screws.
Trim the part of the sealing strips which extend beyond the hotplate base
fig.3
fig.4
Gas connection
Before connecting the appliance to the gas supply, first remove the plastic plug on which is press-
fitted into the gas inlet union; to remove, just pull it off.
1. Check the ‘gas type’ sticker attached to the hotplate. Details of the injector sizes used are recorded on the
data plate located on the base of the appliance.
2. This appliance shall be installed in accordance with installation requirements of the local gas authority of
the appropriate installation code.
3. Before installing the hotplate consider the location of the gas supply and routing the gas line.(Refer fig.5B)
fitted into the gas inlet union; to remove, just pull it off.
1. Check the ‘gas type’ sticker attached to the hotplate. Details of the injector sizes used are recorded on the
data plate located on the base of the appliance.
2. This appliance shall be installed in accordance with installation requirements of the local gas authority of
the appropriate installation code.
3. Before installing the hotplate consider the location of the gas supply and routing the gas line.(Refer fig.5B)