Westinghouse Three-Light Indoor Chandelier 6900000 Instruction Manual

4

NOTE: Underwriters Laboratories (UL) does not require all fixtures to have ground wires.  These fix-
tures meet all UL specifications.

1.  Turn off power at circuit box to avoid possible electric shock.
2. Attach mounting bar (A) to outlet box (B) with outlet box screws (C) (not included).
3. If not pre-assembled; thread hex nut 1 (D1), lock washer (E), hex nut 2 (D2) and screw collar

(F) onto mounting nipple (G) making sure you leave at least 1/4 “ space between hex nut 1 (D1) 
and hex nut 2 (D2).

NOTE: Assemble the entire fixture on the floor.  Be sure the canopy (H) (not shown to scale) and the
screw collar ring (I) are positioned on the chain (J) as shown in figure 1.

4. To assemble fixture, unfold fixture arms (K) to proper position.
5.

Screw center pipe (L) onto the top of the fixture body (M) until snug.

6. Insert side pipe(s) (N) into hole beneath top cover (O), then insert bottom of side pipe(s) (N) into 

holes in fixture arm(s) (K).

7. Screw fixture loop (P) onto nipple (Q) fixture top cover (O) (if applicable).
8. Install decorative cap (R) beneath fixture plate (S) and secure with ball nut (T).
9. Place glass shade(s) (U) over socket(s) (V) and secure with spacer(s) (W) and retaining ring(s) (X) 

using tool (Z).

10. Install lamp(s). Do not exceed recommended wattage.

NOTE: It may be necessary, and is recommended, to use two people when attaching the fixture to the
mounting bar (A) and completing the wiring and adjustments.

11. Open 1 link on bottom end of chain (J), and attach to fixture loop (P).  Securely close loop 

on chain (J).

12. Determine desired chain (J) length and shorten accordingly.  Lace fixture wires up through 

every other link of chain (J), screw collar ring (I), canopy (H), screw collar (F) and out through top 
of mounting nipple (G). Attach top of chain (J) to screw collar (F).

13. Hook mounting nipple (G) into opening of mounting bar (A) so that hex nut 2 (D2) sits 

firmly behind the lip of mounting bar (A) and tighten hex nut 1 (D1) (see inset 1).

14. Connect fixture wires from top of mounting nipple (G) to the outlet box wires with wire 

connectors (AA) (see inset 2).  

15.  To connect wires, take black fixture wire (group A from fig. 2 on page 11) and place evenly

against black outlet box wire. Do not twist wires.

16.  Fit wire connector (AA from fig. 1) over wires and twist until there is a firm connection. If wire 

connector (AA) easily comes off, reattach wire connector (AA) and check again for a firm connection.

17.  Repeat steps 15 and 16 with the white (group B from fig. 2) fixture wire and outlet box wires.
18.  Partially thread green grounding screw (BB) into side hole (CC) on mounting bar (A)(see fig.1.)

19  Wrap ground wire from fixture around green grounding screw (BB) leaving enough excess 

wire to then connect ground wire and outlet box wire with wire connector (AA),
if applicable.

20.  Tighten green grounding screw (BB). Do not over tighten.

21.  Tuck wires inside outlet box (B).

22. Raise canopy (H) over outlet box (B) and secure screw collar ring (I) onto screw collar (F) 

(see insert 2).

NOTE: If adjustment is necessary for proper canopy (H) fit, loosen hex nut 1 (D1) to raise fixture, or
loosen hex nut 2 (D2) to lower fixture.  Lower or raise mounting nipple (G) accordingly and retighten
both hex nut 1 (D1) and hex nut 2 (D2).

23.  Turn power back on at circuit box.

12 pg_W-301_EFS  1/29/07  9:25 AM  Page 4