Blaupunkt HANNOVER CR 67 User Manual
12
Instructions — General Operation
See Traffic Safety & Precautions on page 3.
“Press” means a momentary press of less than 1/2 second. All presses requiring more than 1/2
second are followed by beep.
second are followed by beep.
“Time Out” When additional button presses are anticipated to complete a procedure, the unit will
automatically exit the procedure after 4 seconds of inactivity.
automatically exit the procedure after 4 seconds of inactivity.
Ignition-Off Clock Recall / Turning Unit On
Vehicle ignition must be on. To turn unit on, press ON Button (2) or insert a tape.
Vehicle ignition must be on. To turn unit on, press ON Button (2) or insert a tape.
Ignition-On / Turning Unit Off
Press the ON Button to turn the unit off.
Press the ON Button to turn the unit off.
Release for Detachable Faceplate
Push REL to detach face. Already-inserted cassette remains in unit. Current settings and source
mode are stored. If power was not switched off before face removed, unit will automatically
power-on when face is reattached.
Push REL to detach face. Already-inserted cassette remains in unit. Current settings and source
mode are stored. If power was not switched off before face removed, unit will automatically
power-on when face is reattached.
Power (ON) On/Off
When ignition on, press ON or insert a disc to turn unit on. Last-used source becomes active,
unless unit is turned on by inserting tape, in which case tape player becomes active.
When ignition on, press ON or insert a disc to turn unit on. Last-used source becomes active,
unless unit is turned on by inserting tape, in which case tape player becomes active.
Power Off
Press ON to turn unit off. Unit stores current settings for source, station or track, etc. Antenna/
amplifier trigger wire shuts off voltage. (If faceplate still attached, display switches to clock.)
Press ON to turn unit off. Unit stores current settings for source, station or track, etc. Antenna/
amplifier trigger wire shuts off voltage. (If faceplate still attached, display switches to clock.)
Setting the Clock
Turn the unit on. Press the CLK Button for four seconds until the clock starts blinking.
(The display will change after two seconds. Ignore this and continue to hold for two more
seconds.) Once the clock starts blinking, Press the /\ to set the hour, and press the V Button to
set the minutes. (To change the minute indicator to the nearest hour (:00), you can press the
MUTE Button. Press the CLK Button again to activate the clock.
Turn the unit on. Press the CLK Button for four seconds until the clock starts blinking.
(The display will change after two seconds. Ignore this and continue to hold for two more
seconds.) Once the clock starts blinking, Press the /\ to set the hour, and press the V Button to
set the minutes. (To change the minute indicator to the nearest hour (:00), you can press the
MUTE Button. Press the CLK Button again to activate the clock.
Changing the Information Displayed
You can temporarily change the information shown in your unit’s display. You can also select
which information has “display priority” and is shown in the display except for moments when
adjustments are made.
You can temporarily change the information shown in your unit’s display. You can also select
which information has “display priority” and is shown in the display except for moments when
adjustments are made.
• To change the display priority, press the CLK Button for two seconds. The display priority
changes. The display priority choices are clock or radio frequency / ”TAPE”.
• To change the display temporarily, press and release the CLK Button to access the desired
information.* After
four seconds, the display changes back to the priority information.
Source (SRC)
Use SRC to select source - AMT, FM1, FM2, FMT or cassete (if already inserted).
Use SRC to select source - AMT, FM1, FM2, FMT or cassete (if already inserted).
BA Hannov. CR67 SEA gb®
29.04.2002, 13:29 Uhr
12