Sunfire TGR401 User Manual

Page of 69
User's Manual
39
CHAPTER 5
Manual Setup
The following On Screen Display 
(OSD) menus are used to enter and 
make three main adjustments:
 
•  Speaker Size
 
•  Level Calibration
 
•  Speaker Distance
 
This setup needs to be done 
when you use your system for 
the  rst time, or if you change 
anything such as the ampli ers or 
speakers, or the speaker posi-
tion. The calibration is also a good 
way to check that your system is 
working correctly. These adjust-
ments are made using the OSD 
as follows:
1.  With the remote control set to 
operate the TGR-401, press the 
MENU button to bring up the 
MAIN Menu of the OSD on your 
TV.
2.  Use the navigation pad left, right, 
up and down buttons to navigate 
through the menus in the next 
steps.
 
NOTE: Quit the OSD at any time 
by pressing the nearby EXIT but-
ton. Any changes will be saved. 
There is no need to navigate back 
through previous pages, unless 
you want to make more changes.
 
The TGR-401 front panel display 
shows the same messages as the 
OSD.
3.  In the MAIN Menu, select SETUP, 
and from there select the SPEAK-
ERS Menu.
4.  In the SPEAKERS Menu, select 
the SPEAKER SIZE Menu. Use 
the navigation pad to set the size 
of each speaker to Large, or set to 
OFF for those speakers which are 
not present. For speakers with the 
bass redirected to the subwoofer, 
set to 90 Hz. This is a good start-
ing point. Return to the SPEAK-
ERS Menu when you are  nished.
5.  In the SPEAKERS Menu, select 
the DISTANCE Menu. Enter how 
far each speaker is from your 
listening position. (Measure the 
distance with a tape measure.)
6.  Turn down the main volume 
before you begin the level cali-
bration, or it can be loud. In the 
SPEAKERS Menu, select the 
LEVEL CALIBRATION Menu to 
adjust the output of each speaker. 
A test noise plays in each se-
lected speaker. Use the remote's 
volume buttons to increase the 
starting volume to a comfortable 
level, then use the remote's navi-
gation buttons to adjust the level 
of each speaker in turn, until they 
are all playing at the same level. 
Return to the SPEAKERS Menu 
when you are  nished.
7.  Press the remote’s EXIT button to 
quit the OSD. Now the TGR-401 
is setup correctly and ready for 
action.
LEVEL CALIBRATION
DB
CHOICES
FRONT LEFT
0
(-20 TO +20 IN 0.5 DB STEPS)
CENTER
0
FRONT RIGHT
0
SURR RIGHT
0
BACK SURR R
0
BACK SURR L
0
SURR LEFT
0
SUB
0
SPEAKERS
AUTO SETUP
SPEAKER SIZE
DISTANCE
LEVEL CALIBRATION
EQ
BINDING POSTS
DISTANCE
FT
CHOICES
FRONT LEFT
0.0
0.0 - 25.0 FEET (6 INCH STEPS), 0 - 7.5 
METERS (0.15 METER STEPS)
CENTER
0.0 
FRONT RIGHT
0.0
SURR RIGHT
0.0
BACK SURR R
0.0
BACK SURR L
0.0
SURR LEFT
0.0
SUB
0.0
UNITS
FEET
FEET/ METERS
SPEAKER SIZE
CHOICES
FRONT
90HZ
LARGE,40,45,50,55,60,65,...150
CENTER
90HZ
OFF, LARGE,40,45,50,55,60,65,...150
SURROUND
90HZ
OFF, LARGE,40,45,50,55,60,65,...150
BACK SURR
90HZ
OFF, LARGE,40,45,50,55,60,65,...150
NUM BACK 
SPKRS
2
N/A,1,2
SUBWOOFER
90HZ
OFF, 40,45,50,55,60,65,...150
SUBWOOFER 
MODE
NORM
NORMAL, ENHANCED
SETUP
INPUTS 
SPEAKERS 
VIDEO 
MAIN ZONE 
ZONE 2 
CONTROL 
DIGITAL OUT
DN MIX/THRU
DIMMER LOW/MEDIUM/HIGH
MAIN MENU
TRIMS 
TONE CONTROLS 
MODES
PRESETS 
SETUP