Harman INVINCIBLE PELLET INSERT Owner's Manual
10
ESP CONTROL
Feed adjuster
Sets the maximum feed
rate
Sets the maximum feed
rate
Test
Runs all motors at
full speed for two
minutes to check
operation. After two
minutes the stove
will go to minimum
burn and the blowers
will alternate from
high to low every two
minutes to remind
you that you are still
in "Test Mode".
Runs all motors at
full speed for two
minutes to check
operation. After two
minutes the stove
will go to minimum
burn and the blowers
will alternate from
high to low every two
minutes to remind
you that you are still
in "Test Mode".
Distribution Blower
speed adjustment range.
speed adjustment range.
Status light error messages:
1 Blink: Indicates control board self diagnostic
failure. This requires a manual reset*.
2 Blinks: Indicates that the feeder position switch
has not sensed the slide plate in the home position
for 30 minutes. This means that the slide plate may
be stuck do to a foreign object in the fuel or the
switch has failed. If the switch has failed the stove
will operate normally, however if turned to the
"OFF " position the stove will go to minimum burn
and will only shut down when it runs out of fuel. If
the slide plate frees its self the status light will
failure. This requires a manual reset*.
2 Blinks: Indicates that the feeder position switch
has not sensed the slide plate in the home position
for 30 minutes. This means that the slide plate may
be stuck do to a foreign object in the fuel or the
switch has failed. If the switch has failed the stove
will operate normally, however if turned to the
"OFF " position the stove will go to minimum burn
and will only shut down when it runs out of fuel. If
the slide plate frees its self the status light will
automatically reset. If the error continues call your
Harman Dealer.
3 Blinks: Indicates ESP (Exhaust Sensing Probe)
failure. This requires a manual reset*.
4 Blinks: Can occur only in Room Temp Mode
and indicates Room Sensing Probe failed or not
installed. If a Room Sensing Probe is then installed
the status light will automatically reset.
Harman Dealer.
3 Blinks: Indicates ESP (Exhaust Sensing Probe)
failure. This requires a manual reset*.
4 Blinks: Can occur only in Room Temp Mode
and indicates Room Sensing Probe failed or not
installed. If a Room Sensing Probe is then installed
the status light will automatically reset.
* Manual reset, disconnect power cord for a few
seconds and reconnect. If error still occurs call
your Dealer.
seconds and reconnect. If error still occurs call
your Dealer.
Temp dial
Allows you to adjust the Room temperature
in Room Temp Mode using the outer scale
marked in degrees Fahrenheit. It also
allows you to adjust the stove temperature
while in Stove Temp Mode using the inner
scale marked from 1 to 7.
Allows you to adjust the Room temperature
in Room Temp Mode using the outer scale
marked in degrees Fahrenheit. It also
allows you to adjust the stove temperature
while in Stove Temp Mode using the inner
scale marked from 1 to 7.
Mode Selector
Allows you to choose between Room
Temp Mode, Stove Temp Mode, or OFF.
Also allows you to vary the distribution
blower speed by turning the knob to the
high or low side of each mode.
Allows you to choose between Room
Temp Mode, Stove Temp Mode, or OFF.
Also allows you to vary the distribution
blower speed by turning the knob to the
high or low side of each mode.
Status Light
Blinks to Indicate
errors listed below.
Blinks to Indicate
errors listed below.
Indicates Power to
distribution blower.
distribution blower.
Indicates Power to
combustion blower.
combustion blower.
Indicates Power to
the feed motor.
the feed motor.
Power Light
Indicates power to the
control.
Secondary
function: Blinks every
15 seconds when the
feed adjuster is in
"Test Mode". This
verifies feeder switch
operation.
Indicates power to the
control.
Secondary
function: Blinks every
15 seconds when the
feed adjuster is in
"Test Mode". This
verifies feeder switch
operation.