Paslode 900078 User Manual
12
This tool must be operated in a well ventilated
environment, because the tool exhausts carbon
monoxide similar to a chainsaw or lawn mower.
Exposure to carbon monoxide may cause dizziness,
nausea or unconsciousness.
environment, because the tool exhausts carbon
monoxide similar to a chainsaw or lawn mower.
Exposure to carbon monoxide may cause dizziness,
nausea or unconsciousness.
Fasteners
The Paslode Cordless 16 ga. Stapler drives Paslode
®
16 ga. staples. They are made from 16-gauge galvinized
wire and are completely coated for improved holding
power. The use of staples that do not meet Paslode
standards could cause tool damage and will void all
warranty claims.
wire and are completely coated for improved holding
power. The use of staples that do not meet Paslode
standards could cause tool damage and will void all
warranty claims.
Loading Fasteners
When no fasteners are visible, two full strips of Paslode
staples may be loaded. If fasteners are visible, one full
strip may be loaded.
staples may be loaded. If fasteners are visible, one full
strip may be loaded.
In the illustration above you will see how to properly load
fasteners into the Cordless Stapler. To load:
fasteners into the Cordless Stapler. To load:
1. Draw back the follower until it latches with the follower
latch.
latch.
2. Insert one or two strips of Paslode staples onto the rail.
Let them fall forward to the staple guide.
Let them fall forward to the staple guide.
3. Locate the follower behind the staples. Release follower
latch. The constant force spring will locate the follower
behind the staples and apply a constant pressure on
them.
latch. The constant force spring will locate the follower
behind the staples and apply a constant pressure on
them.
Dirt and debris may interfere with proper feeding of fasteners.
Keep the fastener track clean.
Keep the fastener track clean.
Cordless 16 ga. Stapler and
Outdoor Weather
Use the Cordless Stapler outdoors, in clear weather,
when the stapler, fuel cell, and battery are between
20
when the stapler, fuel cell, and battery are between
20
°F (-7°C) and 120°F (49°C).
HOT WEATHER OPERATION
The Cordless Stapler requires cooling of the motor
assembly to operate properly. The fan normally
provides the necessary air flow to permit continuous
operation. Whenever the Cordless Stapler is idle for
extended periods, keep the fuel and tool out of direct
sunlight and in surroundings where temperatures will
not exceed 120
assembly to operate properly. The fan normally
provides the necessary air flow to permit continuous
operation. Whenever the Cordless Stapler is idle for
extended periods, keep the fuel and tool out of direct
sunlight and in surroundings where temperatures will
not exceed 120
°F (49°C). After extended periods of
continuous use, it may be necessary to cool the
Impulse motor by setting tool aside for 10-15 minutes
or until the tool operates normally. An overheated tool
may not drive staples completely or may operate
erratically.
Impulse motor by setting tool aside for 10-15 minutes
or until the tool operates normally. An overheated tool
may not drive staples completely or may operate
erratically.
COLD WEATHER OPERATION
Fuel cells at cold temperatures lose the required
propellant force. Bring the tool, battery, and fuel cell
above minimum operating temperature without direct
exposure to flame, and check the battery.
propellant force. Bring the tool, battery, and fuel cell
above minimum operating temperature without direct
exposure to flame, and check the battery.
Preparing the Cordless 16 ga. Stapler for Use
CAUTION
CAUTION
The Cordless Stapler should not be used in the rain
or where excessive moisture is present. The use of
the Cordless Stapler under these conditions may
result in damage to tool components and cause tool
to malfunction.
or where excessive moisture is present. The use of
the Cordless Stapler under these conditions may
result in damage to tool components and cause tool
to malfunction.