Behringer Digital Pro Mixer DDM4000 User Manual

DIGITAL PRO MIXER DDM4000 User Manual

Automatically detecting beats with AUTO BPM:
The BPM Counter detects the tempo of the signal source assigned to 

the Effect section. The signal source is shown in the BPM section of the 

display. (Assigning the signal source to the BPM/Effect section is described 

in Chapter 4.1.1.)
1)  Make sure that “Auto BPM” is activated. When active, the AUTO BPM 

push button  

(50)

  shines yellow and the BPM indicator flashes on the display.

2)  Now the BPM Counter determines the BPM value of the played signal.  

It is constantly brought up to date to be able to respond immediately to 

any tempo changes.

Manually detecting beats with TAP:
1)  Make sure that Tap Mode is activated. When active, the AUTO BPM/TAP 

push button  

(50)

  shines blue and the BPM indicator shows “Manual.”

2)  Tap the TAP push button  

(50)

  (at least 2x) in the rhythm of the music, 

which results in a constant BPM value. Here’s a tip: while tapping,  

listen in on the signal using the headphones.

3)  The BPM value can always be readjusted by tapping over and over again.

The MIDI Clock is used as a time reference for the Bounce function. In addition, 

the MIDI Clock is given out at the MIDI output. This allows you to synchronize 

external devices, which are able to receive MIDI Clock (such as drum machines 

and grooveboxes) with the DDM4000.

(53)

(52)

(51)

Fig. 4.7: BPM section

Press the push button  

(52) 

 to start and stop the MIDI Clock.

You can adjust the tempo of the MIDI Clock. Alternatively, the MIDI Clock can also 

be synchronized with one of the two BPM Counters:

MIDI BPM:
When in MIDI BPM Mode, “MIDI BPM” appears in the middle of the display 

below the BPM indicator of the MIDI Clock. Adjust the tempo by turning the 

CONSOLE SETUP knob  

(51)

. It is possible to make bigger value jumps by pressing 

and simultaneously turning the knob.

FX 1/FX 2 BPM:
To transmit the detected tempo of the BPM Counter to the MIDI Clock, 

press one of the ADJUST push buttons  

(53)

. By pressing the left BEAT push button, 

the MIDI Clock adopts the tempo of the left BPM Counter. By pressing the right 

BEAT push button, the MIDI Clock adopts the tempo of the right BPM Counter. 

The assignment is indicated by displaying “FX 1 BPM” or “FX 2 BPM.”
Cancel the assignment by turning the CONSOLE SETUP knob to specify 

your own tempo.
The tempo of the MIDI BPM can also be transmitted to the BPM Counter. Hold the 

left or right ADJUST push button  

(53)

  (or both at the same time) while selecting 

the tempo with the CONSOLE SETUP knob  

(51)

. This function is useful when 

assigning effects to a channel which is configured as MIDI controller so that the 

Auto BPM function does not work.

(54)

(60)

(61)

(64)

(66)

(65)

(63)

(62)

(59)

(58)

(57)

(56)

(55)

Fig. 5.1: Sampler section

A sampler is a device used to record and play back audio signals. 

The DDM4000’s sampler lets you record two tracks which then can be 

played back. These tracks are single short sequences, vocal phrases, rhythmic 

loops or even longer song passages. Any audio signal fed to the mixer can be 

used as signal source, usually found on the stereo channels, the Microphone 

channel and the stereo sum. The maximum recording duration is 32 seconds. 

The samples can be played back in various ways (as infinite loop/loop, one time, 

forward, reverse).