Viking VRCO5240DXSS Installation Instruction
13
Installation
Any finished flooring should be protected
with appropriate material to avoid damage
from moving the unit.
with appropriate material to avoid damage
from moving the unit.
If unit has been laid on its back or sides,
place unit upright and allow minimum of 24
hours before connecting power.Re-installl
the doors by removing the upper pivot pin
completely, sliding the door onto the lower
pivot pin and re-installing the upper pivot
pin and fastening tightly. Before moving the
unit, make sure the door is secured to the
cabinet (tape may be required to hold the
doors closed).
place unit upright and allow minimum of 24
hours before connecting power.Re-installl
the doors by removing the upper pivot pin
completely, sliding the door onto the lower
pivot pin and re-installing the upper pivot
pin and fastening tightly. Before moving the
unit, make sure the door is secured to the
cabinet (tape may be required to hold the
doors closed).
1. Plug the unit into the 15 amp grounded
outlet located in the installation opening.
With power applied to the unit, check that
the lighting and cooling function operate
properly, then turn off power to the wall
outlet at the circuit breaker.
With power applied to the unit, check that
the lighting and cooling function operate
properly, then turn off power to the wall
outlet at the circuit breaker.
CAUTION
3. If all surfaces are level:
a. Measure from the floor to the bottom
of the front edge of the countertop
b. Measure the rear of the unit cabinet
from the floor to top of cabinet, at
back corners
back corners
c. Adjust rear legs so B measurement
equals A measurement. Using an
adjustable wrench or pliers, turn legs
counterclockwise to raise the unit or
clockwise to lower the unit
adjustable wrench or pliers, turn legs
counterclockwise to raise the unit or
clockwise to lower the unit
4. Slide the cabinet into position, making
sure the rear cabinet leveling legs slide
under the anti-tip devices. Push the
cabinet into the opening until the bottom
front edge of the cabinet is flush with the
surrounding cabinetry or the leveling legs
are tight with the anti-tip devices.
under the anti-tip devices. Push the
cabinet into the opening until the bottom
front edge of the cabinet is flush with the
surrounding cabinetry or the leveling legs
are tight with the anti-tip devices.
IMPORTANT: The rear cabinet leveling legs
must be engaged under the anti-tip
brackets.
must be engaged under the anti-tip
brackets.
5. Shim the front of the unit so the front face
is flush with surrounding cabinetry. Adjust
the front legs to support the countertop
at the shimmed height. Using an
adjustable wrench or pliers, turn legs
counterclockwise to raise the unit or
clockwise to lower the unit. Countertop
should be resting on top of the unit.
the front legs to support the countertop
at the shimmed height. Using an
adjustable wrench or pliers, turn legs
counterclockwise to raise the unit or
clockwise to lower the unit. Countertop
should be resting on top of the unit.
IMPORTANT: If countertop is not resting
entirely on unit top, shim the countertop to
prevent damage to the countertop.
entirely on unit top, shim the countertop to
prevent damage to the countertop.
To prevent damage to the countertop and
unit underneath, do not place heavy
objects on countertop directly above the
unit.
unit underneath, do not place heavy
objects on countertop directly above the
unit.
CAUTION
Shut off power to the wall outlet before
installing into the opening.
installing into the opening.
WARNING
2. Check that the following are level and
square:
• Front face and interior opening
• Installation opening and floor surface
• Countertop bottom front edge
• Installation opening and floor surface
• Countertop bottom front edge
IMPORTANT: Leveling legs should not be
extended more than 3/ 4” from bottom of
the cabinet.
extended more than 3/ 4” from bottom of
the cabinet.
IMPORTANT: The floor under the unit must
be at the same level as the surrounding
finished floor.
be at the same level as the surrounding
finished floor.