GE WSLS1500HWW Specification Sheet

WSLS1500H 

GE Spacemaker

®

 Stationary 2.6 DOE Cu. Ft. Washer

This kit consists of the following:

1 Wall mounting bracket

2 Bottom Brackets

6-1/4 x 3 inch wood screws

7-1/4 x 1-1/2 inch wood screws

12 washers

Carefully read and follow individual dryer installation 

instructions for exhausting requirements.

These instructions explain two mounting positions for your 24 inch dryer.

 

1.  Obtain two pieces of 2x4 long enough to span at least two wall studs and the width of the dryer.

  2.   Locate wall stud center lines. Mark wall stud center lines on two pieces of 2x4 in relationship to  

position dryer is to be mounted.

  3.   Referring to dimensional drawing, draw a horizontal reference line (72") from the floor to locate upper  

2x4 support.

  4.   Position, level and secure upper 2x4 with four 1/4 x 3 inch wood screws. The bottom of the 2x4 should be  

positioned on reference line.

  5.  Referring to dimensional drawing, draw a horizontal reference line 32" down from the bottom of the upper  

2x4 support.

  6.   Position, level and secure lower 2x4 with two 1/4 x 3 inch wood screws. The center line of the 2x4 should be  

positioned on reference line.

  7.   Referring to figure 1, mount the metal wall bracket 1/8 inch from the bottom of the upper 2x4 support with 

five 1-1/2 inch wood screws.

  8.  Referring to figure 2, remove one screw from each lower rear corner of dryer and, using same screws, secure 

lower brackets (supplied) as shown.

  9.   Dryer is supplied with exhaust at the top, locate and install outside exhaust duct referring to the dimensional 

drawing. For other optional exhaust directions as shown in dimensional drawing (rear and sides) refer to dryer 

installation instruction sheet.

 10.  Position the dryer on the wall mounting bracket and check that the dryer is plumbed.
 11.   If the dryer needs plumbing, use some of the twelve washers supplied with the kit as spacers behind lower  

brackets of figure 2 and secure the dryer to the lower 2x4 support using the remaining 1-1/2 inch wood screws.

WALL  BRACKET

REAR  VIEW

FRONT  VIEW

2 x 4

figure  1

figure  2

wall_bracket_lineart.eps

1

/

8

" MAX

The back of the dryer is not accessible for service or maintenance after 

dryer mounting installation is complete. It is recommended that the dryer be 

checked and electrical installation completed prior to mounting. For service or 

maintenance requiring rear access, the dryer must be removed from the wall.
CauTIOn: DIsCOnneCT eLeCTRICaL CuRRenT BeFORe InsTaLLIng OR  

seRvICIng DRyeR.

The electrical outlet must be located above the dryer, or beside the dryer if adequate 

dryer-to-wall clearance is available. The outlet must be within three feet on a 240 

volt dryer or a 120 volt dryer from the service cord entry on the rear of the dryer.

20" Max.

Opening

120V 20A or

208-240V 30A

3-3/4

3

3

Rear

Exhaust

5-1/8

8

74-1/8

78

74-1/8

Service

Cord

Entry at

Back of

Appliances

Standpipe

33" Minimum
If Less Than 33"

Use Syphon

Break Kit

WH49X228

R.H

EXH

5-1/8

4" Dia.

Exhaust

3-1/8

Both

Sides

33-1/4

38

79-1/4

32

2 x 4

2 x 4

6

24-1/2

DSKS433

DSKS333

WSLP1500

WSLS1500

28

23-7/8

6

120V

15 or 20A

1-1/2

23-1/4

46

23-7/8