Lynx L2600GNG Use & Care Manual
18
|
SEDONA CARE & USE/INSTALLATION
trouBleSHootinG Your Grill... continued
contactinG lYnX cuStoMer care
wIND hITTING GRILL
Wind hitting the grill while in use, especially winds blow-
ing into or across the hood gap from behind, can cause
poor performance and in some cases can cause the control
panel to get dangerously hot.
ing into or across the hood gap from behind, can cause
poor performance and in some cases can cause the control
panel to get dangerously hot.
Steady or gusty winds can pre-
vent the normal exhaust of hot
gases. Locate your grill away
from prevailing winds and
avoid grilling in windy condi-
tions or utilize wind breaks.
vent the normal exhaust of hot
gases. Locate your grill away
from prevailing winds and
avoid grilling in windy condi-
tions or utilize wind breaks.
bURNER GOES OUT
Location
First determine if the problem is being caused by location.
If the grill is subject to high winds, reposition it to provide
some protection.
First determine if the problem is being caused by location.
If the grill is subject to high winds, reposition it to provide
some protection.
Check the flame
Check the gas supply and flame characteristics. (See IN-
DEX: “Flame, Correct Size”)
Check the gas supply and flame characteristics. (See IN-
DEX: “Flame, Correct Size”)
burners seated
Check to ensure that the burners are correctly positioned
in the grill. (See INDEX: “Burner Placement” for further
details.)
Check to ensure that the burners are correctly positioned
in the grill. (See INDEX: “Burner Placement” for further
details.)
Correctly-installed burners should be seated firmly and
level with no side-to-side movement.
level with no side-to-side movement.
bURNER GOES OUT ONLy whEN SET TO “LOw”
The valves on the grill feature an adjustable low setting.
Fluctuations in gas pressure, gas conversion and even in
the quality of the gas itself may affect burner performance
at the “LOW” setting. It could be either too high or too
low. (See INDEX: “Burner Adjustment” for further details.)
the quality of the gas itself may affect burner performance
at the “LOW” setting. It could be either too high or too
low. (See INDEX: “Burner Adjustment” for further details.)
ROTISSERIE wON’T LIGhT
Follow the same procedure as described for the grill burn-
ers to diagnose problems with the rotisserie burner.
ers to diagnose problems with the rotisserie burner.
BE CAREFUL! The rotisserie burner flame may be hard to
see in bright sunny conditions.
see in bright sunny conditions.
ROTISSERIE LIGhTS bUT GOES OUT
AS SOON AS CONTROL IS RELEASED
AS SOON AS CONTROL IS RELEASED
Check the Thermocouple
The control knob must be held in for 30 to 60 seconds after
ignition for the rotisserie burner to stay lit. (See INDEX:
“Lighting the rotisserie” for further details.)
The control knob must be held in for 30 to 60 seconds after
ignition for the rotisserie burner to stay lit. (See INDEX:
“Lighting the rotisserie” for further details.)
If the burner will not stay lit when you release the control
knob, re-light it and hold the control knob in for at least 60
seconds to allow the thermocouple to heat up.
knob, re-light it and hold the control knob in for at least 60
seconds to allow the thermocouple to heat up.
If, after holding the control knob in for at least 60 seconds,
the burner still will not stay lit when releasing the control
knob, contact Lynx Customer Care. (See INDEX: “Contact-
ing Lynx Customer Care” for further details.)
the burner still will not stay lit when releasing the control
knob, contact Lynx Customer Care. (See INDEX: “Contact-
ing Lynx Customer Care” for further details.)
Before calling Lynx Customer Care, please make sure you
have the following information:
• Model number
• Date of purchase
• Proof of purchase by the original owner
• Serial number.
have the following information:
• Model number
• Date of purchase
• Proof of purchase by the original owner
• Serial number.
The serial number can be located on the rating plate which
is located either on the underside of the drip tray, on the
heat shield behind the front panel).
is located either on the underside of the drip tray, on the
heat shield behind the front panel).
For warranty service, contact the Lynx Customer Care
Department for an authorized service agent near you at:
• (888) 289-5969
• www.lynxgrills.com
Department for an authorized service agent near you at:
• (888) 289-5969
• www.lynxgrills.com
Your satisfaction is of the utmost importance to us. If a
problem cannot be resolved to your satisfaction, please
write, fax or email us:
problem cannot be resolved to your satisfaction, please
write, fax or email us:
lynx Professional grills
5895 Rickenbacker Commerce, CA 90040
Service: (888) 289-5969
Tel: (323) 838-1770
Fax: (323) 838-1778
www.lynxgrills.com
Contact Lynx for replacement parts. Parts are shipped
F.O.B. Commerce, CA.
5895 Rickenbacker Commerce, CA 90040
Service: (888) 289-5969
Tel: (323) 838-1770
Fax: (323) 838-1778
www.lynxgrills.com
Contact Lynx for replacement parts. Parts are shipped
F.O.B. Commerce, CA.