Heartland 311500L User Guide
6
Use & Care Guide
cm) min to 69-1/4 (176 cm) max. Mark wall where
studs are located. Fasten anti-tip bracket to the
wall.
studs are located. Fasten anti-tip bracket to the
wall.
Subflooring or floor coverings (ie carpet, tile, wood
floors, rugs) may make your opening smaller than
anticipated.
floors, rugs) may make your opening smaller than
anticipated.
Some clearance may be gained by using the
leveling procedure under
leveling procedure under
Leveling
.
IMPORTANT: Corner Installations Classic: To
allow door to open 90 degrees, corner installa-
tions must allow 4” (10 cm) space between wall
and refrigerator on hinge side. Filler wood strip
recommended for aesthetics.
allow door to open 90 degrees, corner installa-
tions must allow 4” (10 cm) space between wall
and refrigerator on hinge side. Filler wood strip
recommended for aesthetics.
Measuring the Opening
30” Legacy
30” Legacy
(see page 12 #3065 diagram)
If refrigerator is to be installed into a recess verify
and use the following dimensions
1.) Cut out height for refrigerator, where the top of
the refrigerator is completely covered: 67” (171
cm) - space provides the necessary gap above
the refrigerator for tool access to fasten anti-tip
bracket (see details below)
2.) Cut out width for refrigerator’s main body: 30” (77
cm)
3). Max. cutout depth: 27 1/2” (70 cm)
When installing your refrigerator, measure care-
fully. Allow ½" space at top and ½" space behind
the machine compartment cover (located in the
rear) for proper air circulation.
and use the following dimensions
1.) Cut out height for refrigerator, where the top of
the refrigerator is completely covered: 67” (171
cm) - space provides the necessary gap above
the refrigerator for tool access to fasten anti-tip
bracket (see details below)
2.) Cut out width for refrigerator’s main body: 30” (77
cm)
3). Max. cutout depth: 27 1/2” (70 cm)
When installing your refrigerator, measure care-
fully. Allow ½" space at top and ½" space behind
the machine compartment cover (located in the
rear) for proper air circulation.
Anti-Tip Bracket: Every refrigerator includes an
antitip bracket which must be properly installed to
prevent the refrigerator from tipping forward
should downward pressure be applied with both
doors open. To fasten bracket to the wall, distance
from floor to underside of bracket will be 66-1/4”
(169 cm) max. Mark wall where studs are located.
Fasten anti-tip bracket to the wall.
antitip bracket which must be properly installed to
prevent the refrigerator from tipping forward
should downward pressure be applied with both
doors open. To fasten bracket to the wall, distance
from floor to underside of bracket will be 66-1/4”
(169 cm) max. Mark wall where studs are located.
Fasten anti-tip bracket to the wall.
Subflooring or floor coverings (ie carpet, tile, wood
floors, rugs) may make your opening smaller than
anticipated.
floors, rugs) may make your opening smaller than
anticipated.
Some clearance may be gained by using the
leveling procedure under
Leveling
.
IMPORTANT: Corner Installations Legacy: To
allow door to open 90 degrees, corner installations
must allow 3” (7.6 cm) space between wall and
refrigerator on hinge side. Filler wood strip recom-
mended for aesthetics.
allow door to open 90 degrees, corner installations
must allow 3” (7.6 cm) space between wall and
refrigerator on hinge side. Filler wood strip recom-
mended for aesthetics.
Measuring the Opening
36” Legacy
36” Legacy
(see page 13 #3165 diagram)
If refrigerator is to be installed into a recess verify
and use the following dimensions
1.) Cut out height for refrigerator, where the top of
the refrigerator is completely covered: 70” (177.8
cm) - space provides the necessary gap above
the refrigerator for tool access to fasten anti-tip
bracket (see details below)
2.) Cut out width for refrigerator’s main body:
and use the following dimensions
1.) Cut out height for refrigerator, where the top of
the refrigerator is completely covered: 70” (177.8
cm) - space provides the necessary gap above
the refrigerator for tool access to fasten anti-tip
bracket (see details below)
2.) Cut out width for refrigerator’s main body:
36
½"
(93
cm)
3.) Max. cut-out depth:
24 1/2” (62 cm)
When installing your refrigerator, measure care-
fully. Allow ½" space at top and ½" space behind
the machine compartment cover (located in the
rear) for proper air circulation.
fully. Allow ½" space at top and ½" space behind
the machine compartment cover (located in the
rear) for proper air circulation.
AntiTip Bracket: Every refrigerator includes an
anti-tip bracket which must be properly installed to
prevent the refrigerator from tipping forward should
downward pressure be applied with both doors
open. To fasten bracket to the wall, distance from
floor to underside of bracket will be 68-3/4 (174.6
cm) min to 69-1/4 (176 cm) max. Mark wall where
studs are located. Fasten anti-tip bracket to the
wall
anti-tip bracket which must be properly installed to
prevent the refrigerator from tipping forward should
downward pressure be applied with both doors
open. To fasten bracket to the wall, distance from
floor to underside of bracket will be 68-3/4 (174.6
cm) min to 69-1/4 (176 cm) max. Mark wall where
studs are located. Fasten anti-tip bracket to the
wall
Subflooring or floor coverings (ie carpet, tile, wood
floors, rugs) may make your opening smaller than
anticipated.
floors, rugs) may make your opening smaller than
anticipated.
Some clearance may be gained by using the
leveling procedure under
leveling procedure under
Leveling
.
IMPORTANT :Corner Installations Legacy: To
allow door to open 90 degrees, corner installations
must allow 4” (10 cm) space between wall and
refrigerator on hinge side. Filler wood strip recom-
mended for aesthetics.
allow door to open 90 degrees, corner installations
must allow 4” (10 cm) space between wall and
refrigerator on hinge side. Filler wood strip recom-
mended for aesthetics.