Lynx L54PSR2 Owner's Manual

burner goes out

location

loca

first determine if the problem

is being caused by location.

irst determine if the problem

if the grill is subject to high

is being caused by location.

winds, reposition it to provide

some protection.

checK the flame

check the gas supply and

flame characteristics.

heck the gas supply and

(see

indeX: “flame, correct size”)

BuRneRs seated

check to ensure that the

burners are correctly posi-

tioned in the grill.

burners are correctly posi-

(see indeX:

“Burner placement” for further

tioned in the grill.

details.)

correctly-installed burners

should be seated firmly and

orrectly-installed burners

level with no side-to-side

movement.

burner goes out

only

onl

onl WHen set to

“loW”

the valves on the grill feature

an adjustable low setting.
fluctuations in gas pressure,

gas conversion and even in

luctuations in gas pressure,

the quality of the gas itself

gas conversion and even in

may affect burner perfor-

the quality of the gas itself

mance at the “

may affect burner perfor-

low

may affect burner perfor-

” setting.

it could be either too high or

too low.

(see indeX: “Burner

adjustment” for further details.)

rotIsserIe Won’t

lIgHt

follow the same procedure as

described for the grill bur

ollow the same procedure as

ners

to diagnose problems with the

rotisserie burner.

to diagnose problems with the

Be caReful! the rotisserie

burner flame may be hard to

see in bright sunny conditions.

rotIsserIe lIgHts

but goes out as

soon as control Is

released

checK

theRmocouple

the control knob must be

held in for 30 to 60 seconds

after ignition for the rotis-

serie burner to stay lit.

(see

indeX: “lighting the rotisserie”

for further details.)

if the burner will not stay lit

when you release the control

knob, re-light it and hold the

control knob in for at least

knob, re-light it and hold the

60 seconds to allow the ther-

mocouple to heat up.
if, after holding the control

knob in for at least 60

f, after holding the control

seconds, the burner still will

not stay lit when releasing

the control knob, call for

not stay lit when releasing

service.

(see indeX: “obtaining service

from lynx” for further details.)

lIgHts Won’t lIgHt

checK poweR

ensure that the grill is

connected to a live ac

power source and check for

rotisserie motor operation.

Reset tRansfoRmeR

disconnect power from the

grill and wait 5 minutes for

isconnect power from the

the transformer to cool down

grill and wait 5 minutes for

and reset. then reconnect

power. if, after resetting the

transformer and replacing

power.

power. f, after resetting the

f, after resetting the

bulbs, you still do not have

transformer and replacing

power, call for service.

bulbs, you still do not have

Replace the BulB

Replacement bulbs are

halogen, 12 volt, 10

Replacement

max, t3 type with a

g4 bi-pin base.

3 type with a

the glass cover is held in

place by two spring tension

tabs.

place by two spring tension

you may have to loosen

place by two spring tension

the screw to remove the lens.
avoid touching the glass of a

new bulb. halogen bulbs are

very sensitive to the oils found

alogen bulbs are

in human skin. touching the

bulbs may shorten their life.

ouching the

the socket without twisting.
the 27” and 30”grills each

have one halogen light fixture;

he 27” and 30”grills each

all other grills have two light

fixtures.

all other grills have two light

hold the bulb using a paper

towel or other cloth and

old the bulb using a paper

gently press it straight into the

socket.

gently press it straight into the

the glass cover should

gently press it straight into the

be gently snapped back into

place.

be gently snapped back into

pull on

sprIng

tabs to

release

lIgHt

cover