Lynx L54PSR2 Owner's Manual

37

pull off the control knob. 
while holding the valve 

shaft with pliers, insert a 

hile holding the valve 

hile holding the valve 

thin flat-blade screwdriver 

shaft with pliers, insert a 

shaft with pliers, insert a 

into the shaft and, while 

watching the flame, adjust 

it to a minimum stable 

setting.

the amount of air that enters 

a burner is controlled by the 

air shutter

. 

each grill burner is tested and 

adjusted at the factory prior to 

ach grill burner is tested and 

ach grill burner is tested and 

shipment.  However, fluctua

adjusted at the factory prior to 

adjusted at the factory prior to 

-

tions in gas pressure, gas con-

version and even in the quality 

tions in gas pressure, gas con-

tions in gas pressure, gas con-

of the gas itself may make it 

version and even in the quality 

version and even in the quality 

necessary to adjust the burner. 
The flames of the main brass 

burners should be visually 

checked 

stable with slight yellow tips.  

the bright-blue core should 

stable with slight yellow tips.  

stable with slight yellow tips.  

be about 3/8 inch high with a 

total flame height of about 1 

be about 3/8 inch high with a 

be about 3/8 inch high with a 

ting burner adjustment.

1/2 inches. 
The flames should burn 

quietly. (no “torch” sounds) 

and they should not “lift” up 

quietly. (no “torch” sounds) 

quietly. (no “torch” sounds) 

from the burner.

and they should not “lift” up 

and they should not “lift” up 

If your flames do not match 

those indicated in the photo, 

ensure that the air shutter and 

those indicated in the photo, 

those indicated in the photo, 

burner ports are free and clear 

of dirt, debris, or spider webs. 

burner ports are free and clear 

burner ports are free and clear 

f clear, then adjust the air 

of dirt, debris, or spider webs. 

of dirt, debris, or spider webs. 

shutter. 

t is locked in place by a screw 

which must be loosened 

t is locked in place by a screw 

t is locked in place by a screw 

before adjusting. once 

adjusted retighten the screw. 

Remove the racks and 

briquette trays.
lift out the burner, loosen 

the set screw and then put 

the burner back in place 

the set screw and then put 

the set screw and then put 

and light it.

the burner back in place 

the burner back in place 

If the flame is excessively 

yellow, indicating insuf-

If the flame is excessively 

If the flame is excessively 

ficient air, CAREFULLY turn 

yellow

yellow, indicating insuf-

, indicating insuf-

the air shutter counter-

clockwise to allow more air 

to the burner. 
If the flame is noisy (sounds 

like a torch) and tends to 

Be extremely careful 

around hot Burners 

and other grill parts.

lift away from the burner, 

indicating too much 

air, turn the air shutter 

clockwise. 
after the burner cools 

down, remove it, tighten 

the air shutter set screw 

and reinstall the burner, 

briquette trays and grill 

racks.

briquette trays and grill 

briquette trays and grill 

finally, before leaving, check 

all the burners for proper 

inally, before leaving, check 

inally, before leaving, check 

operation.  make sure the 

ners for proper 

ners for proper 

control knobs turn freely and 

operation.  

operation.  

completely through their full 

control knobs turn freely and 

control knobs turn freely and 

range.

for technical assistance call:
lynx