Lynx L30PSR2 Owner's Manual

note:
lynx built-in grills ar

e intended

either for installation in a

ynx built-in grills ar

built-in enclosure constructed

of non-combustible materials

or for an installation in a built

in enclosure constructed of

combustible material when

installed with a lynx insulating

jacket (liJ).
for non-combustible applica-

tions, the grill drops into the

or non-combustible applica-

opening shown in the cutout

tions, the grill drops into the

detail drawing

opening shown in the cutout

(see indeX: “gas

Requirements”)

and hangs from

detail drawing

its counter-top trim. a deck is

not required to support it from

its counter-top trim.

the bottom.

not required to support it from

when using the insulated

jacket in a combustible

enclosure, the jacket must be

supported from the bottom by

enclosure, the jacket must be

a ledge on each side or a full

supported from the bottom by

deck beneath the jacket.

(See INDEX: “Gas Requirements”)

pay special attention to the

provisions shown for gas line

ay special attention to the

hook-up.

provisions shown for gas line

the enclosure should have

ventilation holes to prevent

gas build-up in the event of

ventilation holes to prevent

a leak.

gas build-up in the event of

the deck ledges and

gas build-up in the event of

counter should be flat and

he deck ledges and

level. (refer to ansi Z21.58

standard for outdoor cooking

gas appliances, section 1.7

enclosures

ppliances,

for s

ppliances,

elf contained

lp-gas supply systems)
This grill requires that a 120

volt, 60 hertz, 15 amp

This grill requires that a 120

gfi

This grill requires that a 120

certified outlet be installed by

volt, 60 hertz, 15 amp

a qualified electrician.

certified outlet be installed by

clearance to com-

bustIble materIals:

minimum clearance from the

sides and back of the grill to

adjacent combustible con-

struction below the top of

unit are 12” from the sides

struction below the top of

and back.
dégagement minimal entre

les parois latérales et l’arrière

de l’appariel et la construc-

les parois latérales et l’arrière

tion combustible au-dessous

de l’appariel et la construc-

du panneau supérieur de

l’appareil (30 cm à partir des

du panneau supérieur de

parois latérales et 30 cm à

l’appareil (30 cm à partir des

partir de l’arrière).

parois latérales et 30 cm à

minimum clearance from

sides and back of unit to

adjacent combustible con-

struction extending above the

unit is 18” from the sides and

struction extending above the

back.
dégagement horizontal

minimal entre les parois

latérales et l’arrière de

minimal entre les parois

l’appariel et la construc-

tion verticale combustible

l’appariel et la construc-

rear Hood clearance:

A 3 inch clearance is required behind the grill to allow the front

hood to open.

A 3 inch clearance is required behind the grill to allow the front

the grill exhausts combustion products and cooking greases to

the back. Never locate the grill where this exhaust will be difficult

he grill exhausts combustion products and cooking greases to

to clean.

au-dessus de l’appareil (45.7

cm à partir des parois

au-dessus de l’appareil (45.7

latérales et 45.7 cm à partir

cm à partir des parois

de l’arrière).

latérales et 45.7 cm à partir

do not use this appliance

under overhead combustible

o not use this appliance

surfaces.
ne pas utiliser cet appareil

sous une surface combus-

e pas utiliser cet appareil

tible.
a minimum of 6” of clearance

is needed on the left side of

the grill above the counter

top for the motor and skewer.

the grill above the counter

if the grill is to be placed into

a combustible enclosure, an

f the grill is to be placed into

approved insulated jacket

is necessary and is available

approved insulated jacket

only from your

is necessary and is available

lynx dealer

ynx dealer

lynx insulated jackets have

been designed and tested

specifically for your Grill.

been designed and tested