Gaggenau AL400721 Brochure
Bar width
min. 40
Silicone
adhesive
adhesive
approx. 26
Fitting retaining bracket when installing from below
350
338
558
546
R 28.5
GN 710 110 cut-out dimensions for installing flush with surrounding surfaces
R 20
129.5
R 28.5
R 20
322
311
119
GN 710 280 cut-out dimensions for installing flush with surrounding surfaces
Recess measurement for installing
flush with surrounding surfaces
Silicone adhesive
1.25
2
45°
Overflow recess
10
5
Overflow
30°
Accessories
351
GN 710 110
Stainless steel
Width 557 mm, Depth 349 mm
GN 710 280
Stainless steel
Width 321 mm, Depth 128 mm
Stainless steel
Width 557 mm, Depth 349 mm
GN 710 280
Stainless steel
Width 321 mm, Depth 128 mm
Special accessories
GN 880 230
Synthetic cutting board GN 2/3
GN 880 230
Synthetic cutting board GN 2/3
325 mm long, 352 mm wide.
GN 880 280
Synthetic cutting board GN 2/8
Synthetic cutting board GN 2/8
325 mm long, 131 mm wide.
GN 114 130
Stainless steel cooking insert GN 1/3
Stainless steel cooking insert GN 1/3
Unperforated, 40 mm deep, 1.5 l.
GN 114 230
Stainless steel cooking insert GN 2/3
Stainless steel cooking insert GN 2/3
Unperforated, 40 mm deep, 3 l.
GN 124 130
Stainless steel cooking insert GN 1/3
Stainless steel cooking insert GN 1/3
Perforated, 40 mm deep, 1.5 l.
GN 124 230
Stainless steel cooking insert GN 2/3
Stainless steel cooking insert GN 2/3
Perforated, 40 mm deep, 3 l.
GN 126 280
Stainless steel cooking insert GN 2/8
Stainless steel cooking insert GN 2/8
Perforated, 65 mm deep, 1.3 l.
Sink
GN 710
- For flush or under-counter
installation
- Work at two levels: in the sink itself
or in the cooking insert
- Compatible with all accessories in
Gastronorm (GN) dimensions
- Any possible combination with
2 sink sizes
Interior dimensions of large sink:
W 541 x H 175 x D 333 mm.
For cooking inserts GN 2/8,
1/3 or 2/3.
For cutting boards GN 2/3 or 2/8.
For cooking inserts GN 2/8,
1/3 or 2/3.
For cutting boards GN 2/3 or 2/8.
Interior dimensions of small sink:
W 305 x H 75 x D 112.5 mm.
For cooking insert GN 2/8.
For cutting board GN 2/8.
For cooking insert GN 2/8.
For cutting board GN 2/8.
Planning notes
Full set of installation material for flush
or under-counter installation included.
Complete set of accessories for
the water outlet with drain eccentric
included.
Drill diameter to install the eccentric is
35 cm (large sink).
Can be installed in a 60 cm wide lower
cabinet.
For flush installation a recess in the
worktop and for the overflow must be
provided.
Because of dimensional tolerances, we
recommend to verify the sink dimen-
sions before installation.
or under-counter installation included.
Complete set of accessories for
the water outlet with drain eccentric
included.
Drill diameter to install the eccentric is
35 cm (large sink).
Can be installed in a 60 cm wide lower
cabinet.
For flush installation a recess in the
worktop and for the overflow must be
provided.
Because of dimensional tolerances, we
recommend to verify the sink dimen-
sions before installation.