GE JSP42SKSS Leaflet
Dimension and installation information are shown in inches.
JSP42SK
GE
®
30" Slide-In Electric Range
Dimensions and Installation Information
Specification Revised 1/08
320642
For answers to your Monogram,
®
GE Profile
™
or
GE
®
appliance questions, visit our website at
ge.com or call GE Answer Center
®
service,
800.626.2000.
All GE ranges are equipped with
an Anti-Tip device. The installation
of this device is an important,
required step in the installation
of the range.
Models are shipped with color-
matched Rear Filler Strip Kit.
Optional Kits For Slide-In
Electric Ranges
(Available at additional cost)
(Available at additional cost)
Lower/Side Trim Kits Accessory Backguards
JXS56 - Lower Trim Kit
JXS56 - Lower Trim Kit
JXS37 - Backguard
JXS86 - Vertical Side Trim Kit
JXS77 - Body Sides
Note: To reduce possiblity of scorching of the side wall
adjacent to the heating elements, it is recommended
a minimum of 6” spacing from adjacent side walls
be allowed for possible extended, high-heat, no-load
operation of heating elements.
Receptacle Location: For all 30” Slide-In Ranges locally
approved flexible service cord or conduit must be
used because terminals are not accessible after range
installation. See shaded area in drawing for location of
electrical outlet box. Recommended outlet locations
allow range to be installed directly against rear wall.
Note: Cabinets installed adjacent to slide-in ranges
must have an adhesion spec of at least 194°.
Installation Information: Before installing, consult
installation instructions packed with product for
current dimensional data.
adjacent to the heating elements, it is recommended
a minimum of 6” spacing from adjacent side walls
be allowed for possible extended, high-heat, no-load
operation of heating elements.
Receptacle Location: For all 30” Slide-In Ranges locally
approved flexible service cord or conduit must be
used because terminals are not accessible after range
installation. See shaded area in drawing for location of
electrical outlet box. Recommended outlet locations
allow range to be installed directly against rear wall.
Note: Cabinets installed adjacent to slide-in ranges
must have an adhesion spec of at least 194°.
Installation Information: Before installing, consult
installation instructions packed with product for
current dimensional data.
KW Rating
240V
11.6
208V
8.7
If you are NOT using the
optional Filler or Backguard:
23-3/16
30
If you are using the optional
Filler or Backguard:
25
30
Listed by
Underwriters
Laboratories
Acceptable
Electrical
Outlet Area
30" Min.
30" Min.
Shave Raised Edge To Clear
31-1/8" Wide Control Panel
Excluding Models JSS28 and JSP39
2-7/8"
To Front
Surface Of
Countertop
20-5/8" Door
Clearance
From Front
Surface of
Countertop
31-1/4
30
25-3/4**
Recommended
6" Min.
From Walls
23-3/16
15" Min.
A/B*
13" Max.
2-1/2
30
25
9/16
7-1/2
2-1/2
Accessory
Backguard
24
36-1/4
*JXS37 is 5-1/4" and JXS32 is 4"
(excluding handle)
**Total depth from wall to
front of closed oven door
including handle is 27-13/16.
35-7/8"–38"
from floor to
countertop
Acceptable
Electrical
Outlet Area
30" Min.
30" Min.
Shave Raised Edge To Clear
31-1/8" Wide Control Panel
Excluding Models JSS28 and JSP39
2-7/8"
To Front
Surface Of
Countertop
20-5/8" Door
Clearance
From Front
Surface of
Countertop
31-1/4
30
25-3/4**
Recommended
6" Min.
From Walls
23-3/16
15" Min.
A/B*
13" Max.
2-1/2
30
25
9/16
7-1/2
2-1/2
Accessory
Backguard
24
36-1/4
*JXS37 is 5-1/4" and JXS32 is 4"
(excluding handle)
**Total depth from wall to
front of closed oven door
including handle is 27-13/16.
35-7/8"–38"
from floor to
countertop