APC BE550G-GR User Manual

© 2009 APC by Schneider Electric. All trademarks are owned by Schneider Electric Industries S.A.S., 
American Power Conversion Corporation, or their affiliated companies.

Input

Voltage

230 Vrms Nominal

Frequency

50/60 Hz (auto sensing)

Brownout Transfer

180 Vrms, typical

Over-voltage Transfer

266 Vrms, typical

Output

Voltage On Battery

230 Vac rms +/- 8%

Total Amperage (8 outlets) 10 Amps (including UPS output)

UPS Capacity (4 outlets)

      550VA/330W        700VA/405W

Frequency - On Battery

50/60 Hz +/-1 Hz

Transfer Time

6 ms typical, 10 ms maximum

Protection 
and Filter

AC Surge Protection

Full time, 451 joules

Phone/fax/DSL Surge 
Protection

Single line (2-wire)

Network Surge Protection

10/100Base-T Ethernet

EMI/RFI Filter

Full time

AC Input

Resettable circuit breaker

Battery

Type

Sealed, maintenance-free lead acid

Average Life

3 - 5 years depending on the number 
of discharge cycles and 
environmental temperature

Physical

Net Weight

 6.4kg             6.8kg

Dimensions (H x W x D)

285 x 230 x 86 mm

(11.2 x 9.1 x 3.4 in)

Operating Temperature

0

o

C to 40

 o

C (32 

o

F to 104 

o

F) 

Storage Temperature

-15

 o

C to 45

 o

C (5 

o

F to 113 

o

F) 

Operating Relative 
Humidity

0 to 95% non-condensing

Operating Elevation

0 to 3000 m (0 to 10,000 ft)

Safety/
Regulatory

BE550G-AZ/BE750G-AZ A-Tick & C-Tick

BE550G-RS/BE750G-RS

GOST

BE550G-GR/BE700G-GR GS 

BE550G-FR/BE700G-FR

CE per IEC62040-1-1 & IEC60884-
1, GS, GOST-PCT

BE550G-UK/BE700G-UK

BE550G-IT/BE700G-IT

EMC Compliance

CE per EN62040-2/EN55022 & C-
Tick

DO NOT RETURN Back-UPS to the place of purchase under 
any circumstances.

1. Verify the battery is connected and that the circuit breaker 

is not tripped.

2. If there are still problems or questions, contact APC.

3. Before contacting APC, have the purchase date, UPS 

model, and serial number (on bottom of unit) available. 

4. If the Technical Support Representative cannot solve the 

problem, the representative will issue a Return Material 
Authorization Number (RMA#) and a shipping address.

5. Pack the unit in its original packaging. If the original 

packaging is not available, ask APC Technical Support 
about obtaining a new set. Pack the unit properly to avoid 
damage in transit. Never use foam beads for packaging. 
Damage sustained in transit is not covered under warranty 
(insuring the package for full value is recommended).

6. Write the RMA# on the outside of the package.

7. Return the unit by insured carrier to the address given to 

you by APC Technical Support.

Replace with a genuine APC battery. Replacement batteries 

can be ordered from www.apc.com (valid credit card 
required). For Back-UPS BE 550, order RBC110. For Back-
UPS BE 700, order RBC17.

The standard warranty is 3 years from the date of purchase in 

the EU, 2 years outside of the EU. APC’s standard procedure 
is to replace the original unit with a factory reconditioned unit. 
Customers who must have the original unit back due to 
assigned asset tags and set depreciation schedules must 
declare such a need at first contact with APC Technical 
Support. APC will ship the replacement unit once the 
defective unit is received by the repair department or cross-
ship upon the provision of a valid credit card number. The 
customer pays for shipping to APC, and APC pays ground 

http://www.apc.com/support

http://www.apc.com

+1 800 555 2725

1 800-652725

000 353 91 7020002725

The UPS can be installed vertically or horizontally to a wall. Use the template to assist 
with installation and a fastener (not included) that can support at least 6.8 kg.

1. Hold the template against the wall surface and use a nail or pin to mark the center of 

each hole.

2. Install a fastener into the wall at the marked locations. Allow 8 mm of the fastener 

to protrude from the wall.

3.Install the unit on the wall, using the fasteners.