Magikitch'n pmn User Manual
MKG SERIES GAS GRIDDLE INSTALLATION & OPERATION
8
22
0
14
0
22
0
14
0
25
0
20
0
150
°C
°F
25
0
20
0
10
0
80
12
0
55
0
26
0
50
0
28
0
24
0
45
0
55
0
150
°C
°F
10
0
80
12
0
50
0
26
0
28
0
24
0
45
0
160
30
0
350
180
400
200
350
180
30
0
160
400
200
3. THERMOSTAT CALIBRATION SECTION:
Each control typically operates a pair of burners with a Snap action, Electric or Solid State. The controls were set at the
factory. However, if the griddle’s surface temperature varies greatly from the setting on the thermostat knob, adjust the
thermostat using the following procedure:
factory. However, if the griddle’s surface temperature varies greatly from the setting on the thermostat knob, adjust the
thermostat using the following procedure:
3.1. CALIBRATION PROCEDURES:
3.1.1. Snap Action and Electric Thermostats:
A.
Light pilots per lighting
instructions.
instructions.
B.
Turn all the control knobs to the
desired temperature setting.
desired temperature setting.
C.
Wait 30 minutes (or 1 hour if
griddle was cold) for surface to
stabilize.
griddle was cold) for surface to
stabilize.
D.
Place a reliable Griddle surface
thermometer,
thermometer,
or test instrument thermocouple, (able to register 300°F), in the location above the thermostat
being calibrated as described in section 2.3.2. Check the temperature every 5 minutes until the temperature
stabilizes and does not change by more than 30°F over a 15 minute time period.
stabilizes and does not change by more than 30°F over a 15 minute time period.
NOTICE:
The adjustment screw in the thermostat is sealed at the factory to protect the calibration, it may be
necessary to remove this seal to be able to adjust the thermostat.
E.
If the average temperature over any burner set is not within +/-15°F of the knob setting (300°F), adjust the
corresponding thermostat. This is done by removing the knob, holding the thermostat knob stem, see picture
this section, (do not allow the stem to turn or the temperature setting will not be accurate), then turn the
adjustment screw located within the center of the stem in small increments. Turn this screw counter
clockwise to increase the temperature, and clockwise to decrease the temperature.
corresponding thermostat. This is done by removing the knob, holding the thermostat knob stem, see picture
this section, (do not allow the stem to turn or the temperature setting will not be accurate), then turn the
adjustment screw located within the center of the stem in small increments. Turn this screw counter
clockwise to increase the temperature, and clockwise to decrease the temperature.
F.
Check the temperature after 15 minutes and repeat adjustment as needed until the correct temperature is
indication on the measuring instrument.
indication on the measuring instrument.
3.1.2. Solid State Thermostat:
A.
Light pilots per lighting instructions.
B.
Turn all the control knobs to the desired
temperature setting.
temperature setting.
C.
Wait 30 minutes (or 1 hour if griddle was
cold) for surface to stabilize.
cold) for surface to stabilize.
D.
Place a reliable Grill surface thermometer,
or test instrument thermocouple, (able to register 300°F), In the
location above the thermostat being calibrated described in the Surface Temperature Check section above.
Check the temperature every 5 minutes until the temperature stabilizes and does not change by more than
30°F over a 15 minute time period. You will need to remember the average temperature for the next step.
Check the temperature every 5 minutes until the temperature stabilizes and does not change by more than
30°F over a 15 minute time period. You will need to remember the average temperature for the next step.
E.
Carefully remove the cap on the thermostat knob with the white indicator line see picture this section. While
holding the knob, loosen the 5/16" nut on the thermostat shaft, (DO NOT REMOVE), once the nut is loose
the knob can be rotated so that the cap line marker is aligned with the actual temperature that the Grill
surface thermometer is indicating.
holding the knob, loosen the 5/16" nut on the thermostat shaft, (DO NOT REMOVE), once the nut is loose
the knob can be rotated so that the cap line marker is aligned with the actual temperature that the Grill
surface thermometer is indicating.
F.
Re-tighten the 5/16" nut while holding the knob in position, (do not allow the stem to turn or the temperature
setting will not be accurate). Replace cap.
setting will not be accurate). Replace cap.