Tyan Computer B5161 User Manuals

Table of Contents

• Chapter 1: Overview

  9
  • 1.1 About the Transport GT20 B5161

    9
  • 1.2 Features

    10
  • 1.3 Unpacking

    12
    • 1.3.1 Opening the Box

      12
    • 1.3.2 Box Contents

      13
    • 1.3.3 Accessories

      14
      • 1 x Tyan driver CD

        14
      • Mounting Bracket x 4

        15
  • 1.4 About the Product

    16
    • 1.4.1 Front View

      16
      • CD-ROM Drive

        16
    • 1.4.2 Rear View

      16
      • Power Supply Socket

        16
    • 1.4.3 LED Definition

      17
    • 1.4.4 Internal View

      19
    • 1.4.5 Motherboard Block Diagram

      20
    • 1.4.6 Motherboard Layout

      21
• CPU socket

  32
• Chapter 2: Setting Up

  9
  • 2.0.1 Before You Begin

    23
  • 2.0.2 Work Area

    23
  • 2.0.3 Tools

    23
  • 2.0.4 Precautions

    24
  • 2.1 Rack Mounting

    25
    • 2.1.1 Installing the Server in a Rack

      25
      • 1. Screw the mounting ear to each side of Transport GT20 as shown using 2 screws from the supplied screws kit.

        26
      • 2. Draw out the inner rails from rail assembly. Install inner rails to left and right sides of chassis using 2 M4-5L(D) screws for each side.

        26
      • 3. Measure the distance between inner side of the front and rear mounting brackets in the rack.

        26
      • 4. Locate the front and rear brackets.

        27
      • 5. Reserve 90mm for Transport GT20 on the front bracket. Secure the front bracket to outer rail with 2 M4-4L(C) screws.

        27
      • 6. Reserve the distance same as in Step 2 on rear bracket. Secure the rear bracket to outer rail with 2 M4-4L(C) screws.

        28
      • 7. Secure the outer rail to the rack using 2 brackets and 4 M4-8L(E) screws for each side (A). Secure the mounting brackets from inside, not outside, of the rack (B).

        28
      • 8. Draw out the middle rail to the latch position.

        29
      • 9. Lift the chassis and then insert the inner slide rails into the middle rails.

        29
      • 10. Push the chassis in and press the latch key (A). Then push the whole system into the rack (B).

        29
      • 11. Secure the mounting ears of chassis to the rack with 2 M4-15L(F) screws.

        30
  • 2.2 Installing Motherboard Components

    31
    • 2.2.1 Removing the Chassis Cover

      31
      • 1. Release the screw on the back side. Then slide the chassis cover in the direction of arrow.

        31
      • 2. Lift the cover off.

        31
    • 2.2.2 Installing the CPU, Heatsink and Air Duct

      32
      • 1. Release the pre-installed air duct. Locate the CPU socket.

        32
      • 2. Remove the cover on the CPU socket.

        32
      • 3. Locate the lever of CPU socket.

        32
      • 4. Press and pull the lever in the direction as illustrated..

        33
      • 5. Open the socket in the direction as illustrated.

        33
      • 6. Place CPU on the socket, ensuring that the edge with triangle mark aims at the edge of socket with triangle mark.

        33
      • 7. Close the cover and secure the CPU socket in the reverse procedures from step 2 to 6.

        34
      • 8. Secure the heatsink with 4 screws. NOTE: Remember to install the washer and nut while installing the screws.

        34
      • 9. Secure the air duct with 2 screws.

        34
    • 2.2.3 Installing the Memory

      35
      • 1. Locate the memory slots on the motherboard.

        35
      • 2. Press the memory slot locking levers in the direction of the arrows as shown in the following illustration.

        35
      • 3. Align the memory module with the slot. The module has indentations that align with notches in the slots.

        35
      • 4. Insert the memory module into the slot as shown.

        35
    • 2.2.4 Installing the PCI Card

      36
      • 1. Push the tab of PCI slot on the rear panel in the direction as shown to release the bracket.

        36
      • 2. Move the bracket to right as shown and then take off the bracket (A).

        36
      • 3. Insert the PCI card in the directions of arrow (B).

        36
      • 4. Push the tab of PCI slot on the rear panel in the direction as shown to fix PCI card.

        36
  • 2.3 Installing the Hard Drive

    37
    • 1. Press the locking lever latch in the direction of arrow (A) and then pull the locking lever open (B).

      37
    • 2. Slide the drive tray out.

      37
    • 3. Place a hard drive into the drive tray.

      37
    • 4. Using 4 HDD screws to secure the HDD.

      38
    • 5. Reinsert the drive tray into the chassis (A), ensuring that the drive tray is completely inserted into the chassis (B).

      38
    • 6. Pressing the locking lever to secure the hard drive tray.

      38
  • 2.4 Installing the Slim FDD (Option)

    39
    • 1. Locate the two FDD rails and screws from the FDD kit. Secure the two rails to FDD using four screws.

      39
    • 2. Connect the FFC cable to FDD.

      39
    • 3. Use a screw driver to take off the door of FDD tray.

      39
    • 4. Insert the FDD module into the tray.

      39
    • 5. Connect the FFC cable to the FDD connector on M1012 adapter board.

      40
    • 6. Locate the FDD cable from FDD kit. Connect the wrinkle side to the connector on M1012 adapter board. Refer to the picture below for the correct direction.

      40
    • 7. Connect the other side to the connector on motherboard.

      40
• Chapter 3: Replacing Pre-Installed Components

  9
  • 3.1 Introduction

    41
    • 3.1.1 Work Area

      41
    • 3.1.2 Tools

      41
    • 3.1.3 Precautions

      42
  • 3.2 Disassembly Flowchart

    43
  • 3.3 Removing the Cover

    44
    • 1. Release the screw on the back side. Then slide the chassis cover in the direction of arrow.

      44
    • 2. Lift the cover off.

      44
  • 3.4 Replacing Motherboard Components

    45
    • 3.4.1 Disconnecting All Motherboard Cables

      45
      • 1. Disconnect ATX power cables

        45
      • 2. Disconnect the Fan, Front Panel, SATA and USB cables. Refer to the mainboard layout on p.13 for the locations.

        45
      • 3. Disconnect the PWM cable .

        45
    • 3.4.2 Removing the Motherboard

      46
      • 1. Release the two screws securing the link bar.

        46
      • 2. Remove the link bar.

        46
      • 3. Remove the eleven screws securing the motherboard to the chassis.

        46
      • 4. Remove the motherboard.

        46
  • 3.5 Replacing the LED Control Board

    47
    • 1. Remove the 2 screws securing the LED control board to the chassis.

      47
    • 2. Pull the LED control board free from the chassis and unplug the ribbon and USB cables from the connector.

      47
    • 3. Remove the three screws securing the LED control board to the bracket

      47
    • 4. Release the LED control board from the chassis. After replacement, insert and secure the unit to the chassis following the reverse procedures from step 1~3.

      48
  • 3.6 Replacing the M1012 Adapter Board

    49
    • 1. Before replacing M1012 adapter board, you must disconnect the four SATA cables connected to the SATA backplane. After that, disconnect all the cables connected to the M1012 adapter board.

      49
    • 2. Remove the Front Panel, LAN/ID LED and Fan Tach cables.

      49
    • 3. Remove the Front Panel Control Board cable.

      49
    • 4. Remove one power cable connected to M1012 adapter board and two power cables connected to SATA backplane.

      50
    • 5. Remove the 6 screws securing the M1012 adapter board. After that, you can release the M1012 adapter board from the chassis.

      50
    • 3.6.1 M1012 Adapter Board Features

      51
    • 3.6.2 M1012 Adapter Board Connector Pin Definition

      52
    • 3.6.3 System Fan Layout

      57
  • 3.7 Replacing the SATA Backplane

    58
    • 1. After removing the M1012 adapter board, you can easily grab the two lables to lift the SATA backplane.

      58
    • 2. Remove the ten screws that secure the bracket to the backplane.

      58
    • 3. Release the backplane free from the bracket.

      58
    • 4. Replace the unit to the chassis following the reverse procedures from step 1 to 3 after done.

      58
    • 3.7.1 S-ATA Backplane (M1204) Features

      59
  • 3.8 Replacing the Cooling Fan

    61
    • 1. Locate the fan connector on the motherboard and unplug the fan cable.

      61
    • 2. Take the fan away from the chassis.

      61
    • 3. Replace the fan into the chassis following the reverse procedures from 1 to 2 after done.

      61
  • 3.9 Replacing the Power Supply

    62
    • 1. Remove the two screws that secure the power supply to the chassis.

      62
    • 2. Remove the screw that secure the fan assembly to the chassis

      62
• Appendix I: BIOS Differences

  1
• Appendix I: BIOS Differences

  1
• Appendix III: Installing SMDC Cards

  1
• Appendix I: BIOS Differences

  1
• Appendix III: Installing SMDC Cards

  1
• Appendix III: Installing SMDC Cards

  1