FireplaceXtrordinair 36A-BI Manual De Usuario
Page 10
OPERATING YOUR APPLIANCE (Continued)
Burning Your Appliance Efficiently
Your Fireplace Xtrordinair is designed to heat your home efficiently with the lowest amount of
creosote build-up and pollutants emitted. The following steps provide a guideline to efficient
burning:
creosote build-up and pollutants emitted. The following steps provide a guideline to efficient
burning:
On cold days, when you wish for high heat output from your appliance, load the appliance
fully after the fire has been established and burn at a medium-high to high burn mode. When
a comfortable heat level in your home has been reached, subsequent loadings would be of
lesser amounts of wood. On warmer days, burn smaller fires, using less wood. This method
will give you the most efficient burn possible.
fully after the fire has been established and burn at a medium-high to high burn mode. When
a comfortable heat level in your home has been reached, subsequent loadings would be of
lesser amounts of wood. On warmer days, burn smaller fires, using less wood. This method
will give you the most efficient burn possible.
Although the fire will burn longer at a lower setting, your appliance will not produce as much
heat and it will increase soot accumulation on the appliance, chimney and glass.
heat and it will increase soot accumulation on the appliance, chimney and glass.
For an overnight burn, establish a hot fire. Before you are ready to retire, completely fill the
appliance with wood. With the controls in the fully open position, let the fire burn intensely for
10 to 15 minutes. Next adjust the draft control so that a low, lazy flame is visible. In the
overnight burn, you should be able to maintain a fire for about 8-10 hours, depending on the
type of wood used, and still have a coal bed, with no visible flame, left to start the morning
fire. To re-establish a fire after an overnight burn, open the controls fully and stir the ashes to
bring hot coals to the surface. Then load more wood to re-establish the fire. If you dampen
the fire down too low, you will not only lower the heat output, but you will be promoting
creosote build-up. It will take a few days of practice to achieve the desired settings.
appliance with wood. With the controls in the fully open position, let the fire burn intensely for
10 to 15 minutes. Next adjust the draft control so that a low, lazy flame is visible. In the
overnight burn, you should be able to maintain a fire for about 8-10 hours, depending on the
type of wood used, and still have a coal bed, with no visible flame, left to start the morning
fire. To re-establish a fire after an overnight burn, open the controls fully and stir the ashes to
bring hot coals to the surface. Then load more wood to re-establish the fire. If you dampen
the fire down too low, you will not only lower the heat output, but you will be promoting
creosote build-up. It will take a few days of practice to achieve the desired settings.
APPROXIMATE COMBUSTION AIR CONTROL SETTINGS
TYPE OF BURN RATE
AIR CONTROL SETTING
Overnight Burn ................................................................................
Fully
Closed
Medium Burn ...................................................................................
Open
1/16"
Medium High Burn..........................................................................
Open 1/8" to 3/8"
High Burn .........................................................................................
Fully
Open
Slide the
control to
the left
for a high
burn
control to
the left
for a high
burn
Slide the control
to the right until
you get a low, lazy
flame for an
overnight burn
to the right until
you get a low, lazy
flame for an
overnight burn
Daily Use of Your Appliance
Some helpful hints: After loading your appliance, open the air control and allow your
appliance to burn vigorously for 20 or 30 minutes. This will assist in the burn-off of any
creosote which accumulates over periods of extended use at low settings.
appliance to burn vigorously for 20 or 30 minutes. This will assist in the burn-off of any
creosote which accumulates over periods of extended use at low settings.