Cisco Systems 150 Prospecto

There are 8 volume levels. To adjust the speaker volume, 
press the       (UP) button to increase, or press the     
(DOWN) button to decrease. The LCD Screen will show 
the digital speaker volume level during adjustment.

The unit is continuously in Receive mode when the
unit is turned ON and not transmitting. When a signal is 
received on the current channel, the receive signal icon
“RX” will be displayed on the LCD Screen. 

Press and hold the TALK (Push to Talk) button to transmit
your voice. The transmit signal icon “TX” will display on 
the LCD Screen and the RED LED indicator will light.
Hold the unit in a vertical position with the Mic 
(Microphone) 5 cm away from the mouth. While holding
the TALK button, speak into the mic (microphone) in a 
normal tone of voice.
Release the TALK button when you have finished 
transmitting.

     To Turn ON;
a.  Press and hold the      (Power) button. A special “beep" 
     sound will be heard and the LCD Screen will display the 
     current channel.
     To switch OFF;
b.  Press and hold the     (Power) button. A special “beep"
     sound will be heard and the LCD Screen will turn blank. 

With the PMR in normal mode, press and release the CALL
button. The unit will transmit a 2-second page tone to the
other unit/s set with the same channel within transmitting 
range.

You can use the CALL button to send a tone to other users on 
the same channel. To activate this feature;

latch

The PMR has 8 available channels. To change channel;
a.  Press the       (Menu) button once, the Channel icon 
     “8 ” will start blinking on the LCD Screen.
b.  While the Channel icon is blinking, press the     (UP) or     
           (DOWN) button to select the desired channel. The 
     channel changes from 1 to 8, or from 8 to 1.
c.  Press the TALK button again to confirm your 
     selected channel.

You can use the Monitor feature to check for weak signals 
on the current channel.
a.   Press the       (Menu) button 3 times. The PMR will
      enter the Monitor mode and hear everything on the 
      current channel.
b.   Press the      (Menu) button again to turn off the 
      Monitor operation and return to standby mode.  

This feature permits the selection of the transmitting power 
level to high or low. At Power High, the PMR will transmit 
at maximum power and at a longer transmission range.
a.  Press the       (Menu) button twice.
b.  Press the     (UP) or      (DOWN) button to select 
     High or Low. The LCD Screen will display "L" when the
     low power is selected. At low power mode, the PMR 
     will transmit at reduced transmitting range but could 
     extend the battery life. 
c.  Press the TALK button again to confirm your 
     selected power level.

CALL button
- Press to send a 
ringing tone to other 
PMR units.

TALK) button 
- Press and hold 
to transmit.

USER GUIDE

Private mobile radio 

Channel Number. Changes 
from 1 to 8 as selected by the 
user.

Displays the Speaker volume 
level.

LCD Screen
-Displays the
current channel 
selection and other
radio symbols.

MENU/     (Power) 
Button 
-(Menu) Press to program 
the PMR settings.
(Power) Press and 
hold to turn the 
PMR unit ON 
or OFF.

    (UP)/    (DOWN) 
buttons - Press to 
change channels, 
volume, and to 
select settings 
during programming.

Displayed when the Power Low is activated.

Displayed when transmitting a signal.

Displayed when receiving a signal.

- Press and hold to 

scan for an active 
channel.

It’s easier to fit the battery pack without
the belt clip in place.

+

+
+

+

+

+

+

When placing the handset in the charger,

.

— never try to burn them or put them anywhere

they could get burnt or punctured.
When you’re not going to use your Latitude 150 for a few weeks,

so it doesn’t leak corrosive substances.

When the battery charge level gets low,an alert tone will be

— they might leak if

you do

.

when you’re charging the batteries.

.

The Latitude 150must be used with the

adapter will result in non-compliance
with EN60065, and will invalidate any
approval given to this apparatus.

If the PMR can detect when the battery charge level gets low.

It takes about

to recharge the batteries fully if they’ve

become completely run down. New batteries can take up to
14 hours to charge fully.

The PMR units have a built-in Power Saver (PS) for maximum

Latitude 150

mainsadapter supplied. Using any other

heard and the RDD LED indicator will flash once every 15 
seconds.When this happens,recharge the batteries.

An alert tone will be  heard and the RED LED indicator will
flash once every 15 seconds. When this happens,will be put
on the handset to charge pod and check the charge LED light.

battery life, but when not in use, turn the unit OFF to 
conserve battery power.

Remove the batteries if the units will not be used for a long 
period of time.

Press and hold down the 

 button. The channel  

number on the LCD  creen changes rapidly until an active 
signal is detected.
When an active signal (one of the 8 channels) is detected,

(OR press the    (UP) button to continue the 

Channel scan performs a search for active signals in a 

other radios without having to manually change to each channel. 

SCAN

continuous loop from channels 1 to 8. This allows you to find

the channel scan pauses on the active channel until the 
active signal stops.
If you press the 

 button while the scan is paused on

an active channel the unit will communicate through the

and

 

the

 

channel

 

scan

 

will

 

be

 

active signal channel,

channel scanning.)

deactivated.

Press and hold the SCAN button to stop the channel 

scanning operation. The unit will return to the channel 

If no action is taken before the detected signal stops then
the scan will continue.

set before the scan was started.

To activate this feature;

s

TALK