Chicago Electric 69684 Manual De Usuario

Page 3

Item 69684 

        

Read all safety warnings and instructions. Failure to follow the warnings and instructions 

1.  KEEP GUARDS IN PLACE and in working order.

2.  REMOVE ADJUSTING KEYS AND WRENCHES. 

Form habit of checking to see that keys and adjusting 

wrenches are removed from tool before turning it on.

3.  KEEP WORK AREA CLEAN. 

Cluttered areas and benches invite accidents.

4.  DON’T USE IN DANGEROUS ENVIRONMENT. 

Don’t use power tools in damp or wet locations, 

or expose them to rain. Keep work area well lighted.

5.  KEEP CHILDREN AWAY. All visitors should 

be kept safe distance from work area.

6.  MAKE WORKSHOP KID PROOF with padlocks, 

master switches, or by removing starter keys.

7.  DON’T FORCE TOOL. It will do the job better 

and safer at the rate for which it was designed.

8.  USE RIGHT TOOL. Don’t force tool or attachment 

to do a job for which it was not designed.

0 – 6

18

16

16

14

6.1 – 10

18

16

14

12

10.1 – 12

16

16

14

12

12.1 – 16

14

12

9.  USE PROPER EXTENSION CORD. Make sure your 

extension cord is in good condition. When using 

an extension cord, be sure to use one heavy 

enough to carry the current your product will 

draw. An undersized cord will cause a drop in line 

voltage resulting in loss of power and overheating. 

Table A shows the correct size to use depending 

on cord length and nameplate ampere rating. 

If  in doubt, use the next heavier gauge. 

The smaller the gauge number, the heavier the cord.

10. WEAR PROPER APPAREL. Do not wear 

loose clothing, gloves, neckties, rings, bracelets, 

or other jewelry which may get caught in moving 

parts. Nonslip footwear is recommended. 

Wear protective hair covering to contain long hair.

11.  ALWAYS USE SAFETY GLASSES. Also use 

face or dust mask if cutting operation is dusty. 

Everyday eyeglasses only have impact resistant 

lenses, they are NOT safety glasses.

12. SECURE WORK. Use clamps or a vise to hold 

work when practical. It’s safer than using your 

hand and it frees both hands to operate tool.

13. DON’T OVERREACH. Keep proper 

footing and balance at all times.

14. MAINTAIN TOOLS WITH CARE. Keep tools sharp 

and clean for best and safest performance. Follow 

instructions for lubricating and changing accessories.

15. DISCONNECT TOOLS before servicing; 

when changing accessories, such as 

blades, bits, cutters, and the like.

16. REDUCE THE RISK OF UNINTENTIONAL 

STARTING. Make sure switch is in 

off position before plugging in.

17. USE RECOMMENDED ACCESSORIES. 

Consult the owner’s manual for recommended 

accessories. The use of improper accessories 

may cause risk of injury to persons.

18. NEVER STAND ON TOOL. Serious injury 

could occur if the tool is tipped or if the 

cutting tool is unintentionally contacted.

19. CHECK DAMAGED PARTS. Before further use 

of the tool, a guard or other part that is damaged 

should be carefully checked to determine that 

it will operate properly and perform its intended 

function – check for alignment of moving parts, 

binding of moving parts, breakage of parts, 

mounting, and any other conditions that may 

affect its operation. A guard or other part that is 

damaged should be properly repaired or replaced.

20. DIRECTION OF FEED. Feed work into 

a blade or cutter against the direction of 

rotation of the blade or cutter only.

21. NEVER LEAVE TOOL RUNNING UNATTENDED. 

TURN POWER OFF. Don’t leave tool 

until it comes to a complete stop.