Cisco Systems AIRCAP1552HAK9 Manual De Usuario
1-22
Cisco Aironet 1550 Series Outdoor Mesh Access Point Hardware Installation Guide
OL-24247-01
Chapter 1 Overview
Hardware Features
Warning
To reduce the risk of fire, use only No. 26 AWG or larger telecommunication line cord. Statement 1023
Caution
To provide inline PoE, you must use the 1500 power injector (AIR-PWRINJ1500-2=). Other power
injectors, PoE switches, and 802.3af power sources cannot provide adequate power, which can cause the
access point to malfunction and cause over-current conditions at the power source.
injectors, PoE switches, and 802.3af power sources cannot provide adequate power, which can cause the
access point to malfunction and cause over-current conditions at the power source.
Caution
The 1500 power injector (AIR-PWRINJ1500-2=) must be used in an indoor environment only.
Caution
When the access point is installed outdoors or in a wet or damp location, the AC branch circuit that is
powering the access point should be provided with ground fault protection (GFCI), as required by Article
210 of the National Electrical Code (NEC).
powering the access point should be provided with ground fault protection (GFCI), as required by Article
210 of the National Electrical Code (NEC).
Note
In the cable configuration, the cable modem is activated only when the access point is powered by POC
or external 12 VDC power. When using only PoE power, the cable modem is deactivated.
or external 12 VDC power. When using only PoE power, the cable modem is deactivated.
The following AC power cord options are available:
•
40-ft (12.2-m) power cord for light pole installations in the US and Canada. One end of the power
cord is terminated with an access point AC power connector and the other end is terminated with an
AC plug (AIR-CORD-R3P-40NA=).
cord is terminated with an access point AC power connector and the other end is terminated with an
AC plug (AIR-CORD-R3P-40NA=).
•
40-ft (12.2-m) power cord for use outside the US and Canada. One end of the power cord is
terminated with an access point AC power connector and the other end is unterminated.
(AIR-CORD-R3P-40UE=).
terminated with an access point AC power connector and the other end is unterminated.
(AIR-CORD-R3P-40UE=).
•
4-ft (1.2-m) streetlight power tap adapter for light pole installations in the US and Canada
(AIR-PWR-ST-LT-R3P=).
(AIR-PWR-ST-LT-R3P=).
Cable Modem (POC)
The access point POC cable modem configuration contains an internal cable modem for connection to
the cable network from the pole-mounted cable lines. The access point can be powered using the 40-to
90-VAC (quasi-square wave AC) power provided by the cable network.
the cable network from the pole-mounted cable lines. The access point can be powered using the 40-to
90-VAC (quasi-square wave AC) power provided by the cable network.
The cable modem supports these main features:
•
Data Over Cable Service Interface Specifications (DOCSIS)3.0
•
Backward compatibility with existing DOCSIS 1.1 and 1.0 networks
Ethernet (PoE) Ports
The access point supports an Ethernet uplink port (POE-In) and a downlink port (POE-Out). The access
point PoE-in port uses an RJ-45 connector (with a liquid tight adapter) to link the access point to the
10/100/1000BASE-T network. The Ethernet cable is used to send and receive Ethernet data and to
optionally supply inline 56-VDC power from the power injector.
point PoE-in port uses an RJ-45 connector (with a liquid tight adapter) to link the access point to the
10/100/1000BASE-T network. The Ethernet cable is used to send and receive Ethernet data and to
optionally supply inline 56-VDC power from the power injector.