CyberPower Systems UP750E Prospecto

 

POWER

ON

BATTERY

USING

USING

BATTERY

ON

POWER

 
 

 

 

K01-U350E0A-01

 

This manual contains important safety instructions. Please read and follow all instructions carefully 
during installation and operation of the unit. Read this manual thoroughly before attempting to 
unpack, install, or operate your UPS. 

 

This equipment can be operated by any individuals with no previous training. 

 

The socket-outlet shall be installed near the equipment and easily accessible. 
 
During the installation of this equipment it should be assured that the sum of the leakage currents of 
the UPS and the connected loads does not exceed 3.5mA. 
 
Attention, hazardous through electric shock. Also with disconnection of this unit from the mains, 
hazardous voltage still may be accessible through supply from battery. The battery supply should be 
therefore disconnected in the plus and minus pole at the quick connectors of the battery when 
maintenance or service work inside the UPS is necessary. 
 
Do not dispose of batteries in a fire, the battery may explode. 
 
Do not open or mutilate the battery or batteries, released electrolyte is harmful to the skin and eyes. 

 

 
Inspect the UPS upon receipt. The box should contain the following: 
UPS Unit; PowerPanel

®

 Software Disk

¯1; Serial Interface Cable (DB-9)¯1; Telephone Cable¯1; 

IEC-IEC Power Cord

¯2; User Manual; PowerPanel

®

 Software User Manual. 

 

 
1. Insure that the equipment plugged into the battery power-supplied outlets does not exceed the 

UPS unit’s rated capacity (350VA/210W for UP350TE, 500VA/300W for UP500TE, 500VA/325W 
for UP500E, 750VA/450W for UP750E). If rated unit capacities are exceeded, an overload 
condition may occur and cause the UPS unit to shut down or the circuit breaker to trip. 

 
2. If the power requirements of your equipment are listed in units other than Volt-Amps (VA), convert 

Watts (W) or Amps (A) into VA by doing the calculations below. Note: The below equation only 
calculates the maximum amount of VA that the equipment can use, not what is typically used by 
the equipment at any one time. Users should expect usage requirements to be approximately 60% 
of below value. 

 

1.              Watts (W) x 2.0 =                    VA or               Amps (A) x 230 =       VA 
 
2. Add the totals up for all pieces of equipment and multiply this total by 0.6 to calculate actual 

requirements. There are many factors that can affect the amount of power that your computer 
system will require. The total load that you will be placing on the battery-powered outlets should 
not exceed 80% of the unit’s capacity. 

 

 
1. Connect the equipment to your UPS outlets. The IEC-IEC power cords coming with the unit are 

used to connect your computer and monitor to the UPS. Items such as copiers, laser printers, 
vacuums, space heaters, or other large electrical devices should not be connected to the UPS. 
Please make sure that the total loads of your equipments are less than the maximum total power 
load of your UPS. 

 
 
 
 
 
 
 
 
 
 

2. Use your computer power cord to connect the UPS to a wall outlet. Please avoid using extension 

cords and adapter plugs. (To maintain optimal battery charge, leave the UPS plugged in at all 
times.)

 

 

 
3. Press the UPS power button to turn it on. The “Power On” indicator will be illuminated in “Green”. 
 
4. Install your software and accessories. To use the software, simply connect the enclosed serial 

interface cable to the serial port on the UPS and an open serial port on the computer. 

 
 
 
 
 
 
 
 
 

 
 
 
 
 

             

 
◆ 

UP350TE/UP500TE                UP500E/UP750E

 

Press the power button to turn the UPS ON or OFF. 

 

◆ 

 
This LED is illuminated when the utility condition is normal and the UPS outlets are 
providing “clean power”, free of surges and spikes. 
 

◆ 

 
This illuminates during utility failure, indicating that the battery is supplying power to 
the battery-power supplied outlets. 
 

 
◆

 
 

The UPS provides battery powered and surge protected

 

outlets for connected equipment to insure temporary 
uninterrupted operation during a power failure and against 
surges and spikes. 

 
◆

 
 
 

The UPS provides surge protected

 

only outlet for connected 

equipments against surges and spikes. 

 

 
◆ 

 
This port allows connection and communication from the DB-9 serial on the computer 
to the UPS unit. The UPS communicates its status to the PowerPanel

®

 software. This 

interface is also compatible with the UPS service provided by Windows 98, Windows 
ME, Windows NT, Windows 2000, Windows XP, Windows Server 2003. 

 
◆ 

 

 

 

 

These ports are the protection for your computer network cable. 
 

 

 

 

CAUTION! Read and follow the IMPORTANT SAFETY INSTRUCTIONS before servicing the battery.   
Service the battery under the supervision of personnel knowledgeable of batteries and their 
precautions. Keep unauthorized personnel away from batteries. If you have questions, contact 
your dealer or call the number in this manual for information on battery replacement. 
CAUTION! Use only the specified type of battery. See your dealer for replacement batteries. 
CAUTION! The battery may present the risk of electrical shock. Do not dispose of batteries in a 
fire, as it may explode. Follow all local ordinances regarding proper disposal of batteries. 
CAUTION! Do not open or mutilate the batteries. Release electrolyte is harmful to the skin and eyes 
and may be toxic. 
CAUTION! A battery can present a high risk of short circuit current and electrical shock. Take the 
following prec

autions before replacing the battery: 

1. Remove all watches, rings or other metal objects. 
2. Only use tools with insulated handles. 
3. DO NOT lay tools or other metal parts on top of battery or any battery terminals. 
4. Determine if the battery is inadvertently grounded. If inadvertently grounded, remove source of 

ground. CONTACT WITH A GROUNDED BATTERY CAN RESULT IN ELECTRICAL SHOCK! 
The likelihood of such shock will be reduced if such grounds are removed during installation 
and maintenance (applicable to a UPS and a remote battery supply not having a grounded 
circuit). 

5. 

Batteries are consider HAZARDOUS WASTE and must be disposed of properly. Contact your 

local government for more information about proper disposal and recycling of batteries. 

6. Turn off and unplug all connected equipment. 
7. Turn the UPS off and unplug it from the AC power source. 

8

. 

Turn the UPS upside down.