Kolpak DA-98 Manual De Usuario
Section 8 – Advanced operations
06/97 – 1.00 – 8-3
1) Go to menu group 7, move the cursor to
Loc
(Func)
, and press
ENTER
:
2) Move the cursor to the function key number,
and use the
UP
and
DOWN
keys to select the
number of the function key memory that you
want to change.
want to change.
3) Use the
LEFT
and
RIGHT
keys to select the field
(hours, minutes, seconds or frames) and use the
UP
and
DOWN
keys to change the value of the
field.
There is an “invisible” field to the right of the
number. Moving the cursor to this field and press-
ing the
number. Moving the cursor to this field and press-
ing the
UP
and
DOWN
keys will “fine-tune” the
whole time value.
8.2.3 Locating to a function key memory
Once a location has been assigned to a function
key, this is the procedure for location to the mem-
ory position:
key, this is the procedure for location to the mem-
ory position:
1) Press the
SHIFT
key.
The
SHIFT
indicator will start to blink.
2) Press the function key corresponding to the
memory to which you want to locate.
The display will show the location point and the
pre-roll time, and the tape will start to locate to the
appropriate location memory.
pre-roll time, and the tape will start to locate to the
appropriate location memory.
3) To use the function keys for their preset
functions as written on the front panel, press
SHIFT
again so that the
SHIFT
indicator goes
out.
8.2.4 Location and playback
If you press the
PLAY
key while the tape is locat-
ing (the
PLAY
key will flash), the tape will start
playing when it reaches the location point.
If you press
PLAY
twice while the tape is locating,
the
PLAY
key will light steadily, the tape will stop
and playback will start immediately.
If you have pressed the
AUTO PLAY
key [12]
before pressing the
SHIFT
key in step 1, (the
AUTO
PLAY
indicator is on), replay will start automati-
cally when the location point is reached.
8.2.5 Repeat function
You can repeat playback continuously between
the two location memory points (
the two location memory points (
Memo 1
and
Memo 2
).
The tape will wind to a little before the first point
(if it is not there already) and start playing. The
off-tape monitoring will start at the first memory
location and continue until the second location is
reached. The tape will then stop playing, and
rewind to a little before the first point and start
playing again.
(if it is not there already) and start playing. The
off-tape monitoring will start at the first memory
location and continue until the second location is
reached. The tape will then stop playing, and
rewind to a little before the first point and start
playing again.
8.2.6 To start repeat play
1) When the two location points have been set,
press the
REPEAT
key [21] .
2) The tape will locate to the first location point
and start playing until the second location
point, rewind to the first location point, and
play again. This process will be repeated.
point, rewind to the first location point, and
play again. This process will be repeated.
While the tape position is between the two location
points, the
points, the
REPEAT
indicator will be lit steadily. It
will flash while the tape position is outside the two
location points.
location points.
3) Stop the repeat function by pressing the
REPEAT
key.
The
REPEAT
indicator will go out.
If the tape is playing, it will continue playing (past
the second location point).
the second location point).
L o c a t e
P o s i t i o n
( F u n c t i o n
K e y )
A B S
F .
1
1 0 : 0 4 : 2 3 : 1 5
NOTE
When we talk about the “first” and the “second” loca-
tions here, we are referring to the earlier and later loca-
tion times.
tions here, we are referring to the earlier and later loca-
tion times.
Memo 1
could be at a later time than
Memo 2
, and hence we would refer to it in this sec-
tion as the “second location point”.