Kolpak DA-98 Manual De Usuario
Section 9 – Synchronization with other DTRS units
06/97 – 1.00 – 9-5
10) On the master machine, hold down
RECORD
and press
PLAY
.
No recording will take place on the source master,
but the tracks will be recorded digitally on a one-
to-one basis to the target slave.
but the tracks will be recorded digitally on a one-
to-one basis to the target slave.
There is no need to carry out any special pre-dub-
bing procedure such as timing the digital output –
the digital and analog outputs are separate.
bing procedure such as timing the digital output –
the digital and analog outputs are separate.
You can use the Track Copy functions on the target
slave machine (see 8.11, “Routing digital inputs”)
to transfer tracks from the source master tape to
different tracks on the target slave. Note that you
cannot combine tracks by this method.
slave machine (see 8.11, “Routing digital inputs”)
to transfer tracks from the source master tape to
different tracks on the target slave. Note that you
cannot combine tracks by this method.
9.4.1 Synchronized formatting
When several units are connected together, you
can format several tapes simultaneously, using one
machine as the master. This can be a very conve-
nient way of saving time and effort.
can format several tapes simultaneously, using one
machine as the master. This can be a very conve-
nient way of saving time and effort.
1) Make sure that all machines are connected
together using the
SYNC
connections, as
described above, and that the last unit in the
chain is terminated.
chain is terminated.
2) Load a blank unformatted tape into each
DTRS unit.
Make sure all tapes are the same length.
3) Press the
CHASE
switch [16] on all of the slave
DTRS units. The indicator will flash.
4) Press
FORMAT/Fs
[6] twice within five seconds,
on each of the DTRS units (master and all
slaves) so that all
slaves) so that all
FORMAT
indicators are lit.
The first time you press the FORMAT/Fs switch,
the indicator will flash. Press it again within five
seconds to select format mode. If you wait more
than 5 seconds, the indicator will stop flashing.
the indicator will flash. Press it again within five
seconds to select format mode. If you wait more
than 5 seconds, the indicator will stop flashing.
If you press the
CLEAR
key [11] while the
FORMAT
indicator is lit steadily, you will cancel
the format operation.
5) Select the same sampling rate (48kHz or
44.1kHz) on each DTRS unit.
Any slave DTRS unit which has a different sam-
pling frequency selected from that selected on the
master will display an error message.
pling frequency selected from that selected on the
master will display an error message.
6) Press and hold
PLAY
and press
RECORD
on the
master. All slave units’
CHASE
indicators will
light steadily, and the tapes will start to be
formatted in synchronization.
formatted in synchronization.
9.4.2 Recording while formatting
As with a single-machine format (see 6.1.2,
“Recording while formatting”), it is possible to
record while formatting.
“Recording while formatting”), it is possible to
record while formatting.
You may want to use this feature when making a
live multi-machine recording, and there has not
been time to format all the tapes in advance of the
performance.
live multi-machine recording, and there has not
been time to format all the tapes in advance of the
performance.
Remember that you should let the tapes run to the
end–you should not halt the formatting/recording
process part of the way through the tape.
end–you should not halt the formatting/recording
process part of the way through the tape.
9.5 Error messages
These error messages refer to DTRS
synchronization:
synchronization:
Appears if the digital cable is not connected.. Re-
connect the correct cable to the
connect the correct cable to the
DIGITAL I/O
connector.
Appears when the sync cable is not connected, the
master has been turned off, or the master’s sam-
pling frequency is different from that of the slave
unit’s. Recheck these parameters.
master has been turned off, or the master’s sam-
pling frequency is different from that of the slave
unit’s. Recheck these parameters.
If either of these messages appears, correct the
fault, and press the
fault, and press the
ESCAPE
key to return to nor-
mal operation.
W A R N I N G !
T D I F ( d u b b i n g ) c a b l e
n o t
c o n n e c t e d
W A R N I N G !
N o
c l o c k
f r o m
M A S T E R
C h e c k
c o n n e c t i o n s
a n d
s e t t i n g s