Jenn-Air JJW8630 Manual De Usuario

Before replacing light bulb, DISCONNECT
POWER TO OVEN. Be sure bulb is cool. Do
not touch a hot bulb with a damp cloth as the
bulb may break.

Use a dry potholder and very carefully un-
screw bulb cover and bulb. Replace with a 40
watt, oven-rated appliance bulb. Bulb with a

1. Do not use abrasive cleaning agents such

• Check if oven controls are properly set.
• Check if oven is properly connected to electri-

cal outlet.

• Check or re-set circuit breaker. Check or

replace fuse.

• Check power supply.

• Clock controls may be set for a delayed bake

function.

• The Oven Control Lockout may have been set.

(See page 4.)

• The light bulb is loose or defective.
• The oven light does not work during self-

cleaning process.

• This is normal for a new wall oven and will

disappear after a few uses. Initiating a clean cycle
will “burn off” the smells more quickly. Turning
on a ventilation fan will help remove the smoke
and/or odor.

• Excessive food soils on the oven bottom. Use

a self-clean cycle.

• Check the “Clean” and “Stop” time settings and

the current time of day on the clock.

• Oven may need longer cleaning time.

brass base is recommended to prevent fusing
of bulb into socket.

Replace bulb cover and reconnect power to
oven. Reset clock.

as steel wool scouring pads or powdered
cleansers as they may scratch the glass.

2. Do not hit the glass with pots, pans,

furniture, toys, or other objects.

3. Do not close the oven door until the oven

racks are in place.

Scratching, hitting, jarring or stressing the
glass may weaken its structure causing an
increased risk of breakage at a later date.

• Excessive spills were not removed prior to self-

cleaning process.

• Check rack position. (See page 5.)
• Voltage into house may be low.

• Food may be positioned incorrectly in oven.

(See “Cooking Made Simple” booklet.)

• Oven not preheated properly.

• The oven may be installed improperly.
• Check the oven rack with a level.
• Stagger pans, do not allow pans to touch each

other or oven wall.

• Check instructions for suggested placement of

pans on oven rack. (See “Cooking Made
Simple” booklet.)

• Oven may not have cooled to safe temperature

after self-cleaning process.

• The pans being used may not be of the size or

material recommended for best results. (See
“Cooking Made Simple” booklet).

• There may not be sufficient room around sides

of the pans for proper air circulation in the
oven.

• Check instructions for preheating, rack posi-

tion and oven temperature.

• Oven thermostat calibration may differ be-

tween old and new ovens. Follow recipe and use
the directions in this guide before calling for
service since the calibration on the previous
oven may have drifted to a too high or too low
setting. (See p. 4 - Adjusting Oven Tempera-
ture.)

• This is normal. The fan will automatically shut off

when the oven is cooled.

• This is the cooling fan and is normal. The fan will

continue to run after use until the oven cools.

• Fault codes are shown in the display as “F” and

a number. If a fault code appears in the display
and beeps sound, press the Cancel pad. If the
fault code and beeps continue after pressing
Cancel, disconnect power to the oven. Wait a
few minutes, then reconnect power to the oven.
If the fault code and beeps still continue, discon-
nect power to the wall oven and call an autho-
rized servicer.

• If the oven is heavily soiled, excessive flare-ups

may result in a fault code during a clean cycle.
Press Cancel pad and allow the oven to cool for
one hour, then reset the clean cycle. If the fault
code and beeps still continue, disconnect power
to the appliance and call an authorized servicer.

• If an error beep sounds (two short beeps) with

no fault code in the display, clean any spill from
key pad area within 30 seconds. If, after 30
seconds the spill is not removed or another
problem exists, an F7 fault code will be dis-
played. Disconnect power to the appliance and
call an authorized servicer.