Kingston Technology 6GB, 1333MHz, DDR3, ECC, CL9, DIMM (Kit of 3) w/Thermal Sensor (Intel) KVR1333D3E9SK3/6GI Hoja De Datos
Los códigos de productos
KVR1333D3E9SK3/6GI
Memory Module Specifications
KVR1333D3E9SK3/6GI
6GB (2GB 256M x 72-Bit x 3 pcs.) PC3-10600
Triple-Channel CL9 ECC 240-Pin DIMM Kit
Triple-Channel CL9 ECC 240-Pin DIMM Kit
Kingston.com
Document No. VALUERAM0827-001.A00 08/03/09 Page 1
DESCRIPTION
ValueRAM’s KVR1333D3E9SK3/6GI is a kit of three
256M x 72-bit 2GB (2048MB) DDR3-1333MHz CL9 SDRAM
(Synchronous DRAM), Intel
256M x 72-bit 2GB (2048MB) DDR3-1333MHz CL9 SDRAM
(Synchronous DRAM), Intel
®
Compatibility Tested, ECC triple-
channel memory modules, based on eighteen 128M x 8-bit
DDR3-1333MHz FBGA components. Total kit capacity is 6GB
(6144MB). Each module’s SPD is programmed to JEDEC
standard latency 1333MHz timing of 9-9-9 at 1.5V. Each 240-
pin DIMM uses gold contact fingers and requires +1.5V. The
electrical and mechanical specifications are as follows:
DDR3-1333MHz FBGA components. Total kit capacity is 6GB
(6144MB). Each module’s SPD is programmed to JEDEC
standard latency 1333MHz timing of 9-9-9 at 1.5V. Each 240-
pin DIMM uses gold contact fingers and requires +1.5V. The
electrical and mechanical specifications are as follows:
FEATURES
• JEDEC standard 1.5V ± 0.075V Power Supply
• VDDQ = 1.5V ± 0.075V
• 667MHz fCK for 1333Mb/sec/pin
• 8 independent internal bank
• Programmable CAS Latency: 5,6,7,8,9,10
• Posted CAS
• Programmable Additive Latency: 0, CL - 2, or CL - 1 clock
• Programmable CAS Write Latency(CWL) = 7(DDR3-1333)
• 8-bit pre-fetch
• Burst Length: 8 (Interleave without any limit, sequential with
• VDDQ = 1.5V ± 0.075V
• 667MHz fCK for 1333Mb/sec/pin
• 8 independent internal bank
• Programmable CAS Latency: 5,6,7,8,9,10
• Posted CAS
• Programmable Additive Latency: 0, CL - 2, or CL - 1 clock
• Programmable CAS Write Latency(CWL) = 7(DDR3-1333)
• 8-bit pre-fetch
• Burst Length: 8 (Interleave without any limit, sequential with
starting address “000” only), 4 with tCCD = 4 which does
not allow seamless read or write [either on the fly using A12
or MRS]
not allow seamless read or write [either on the fly using A12
or MRS]
• Bi-directional Differential Data Strobe
• Internal(self) calibration : Internal self calibration through ZQ
• Internal(self) calibration : Internal self calibration through ZQ
pin (RZQ : 240 ohm ± 1%)
• On Die Termination using ODT pin
• On-DIMM thermal sensor (Grade B)
• Average Refresh Period 7.8us at lower than TCASE 85°C,
• On-DIMM thermal sensor (Grade B)
• Average Refresh Period 7.8us at lower than TCASE 85°C,
3.9us at 85°C < TCASE ≤ 95°C
• Asynchronous Reset
• PCB : Height 1.180” (30.00mm), double sided component
• PCB : Height 1.180” (30.00mm), double sided component
SPECIFICATIONS
CL(IDD)
9 cycles
Row Cycle Time (tRCmin)
49.5ns (min.)
Refresh to Active/Refresh
110ns
Command Time (tRFCmin)
Row Active Time (tRASmin)
36ns (min.)
Power
2.025 W (operating)
UL Rating
94 V - 0
Operating Temperature
0° C to 85° C
Storage Temperature
-55° C to +100° C
Continued >>